Samlexpower SEC-40BRM-230 Owner'S Manual Download

Page: 2 / 24

2 | SAMLEX AMERICA INC.

OwNer'S MaNual |

Index

Section 1

Important Safety Instructions ................................................ 4

Section 2

Description & Application .................................................... 6

Section 3

Design & Principle of Operation ........................................... 7

Section 4

Cooling & Warning for Fan Failure ....................................... 8

Section 5

Front Panel Controls & Indicators ......................................... 8

Section 6

Rear Panel Controls .............................................................. 9

Section 7

Protections ......................................................................... 10

Section 8

Installation & Operation ..................................................... 10

Section 9

Operation of Battery Backup ...............................................11

Section 10

Output Voltage Adjustment ............................................... 13

Section 11

Installation & Removal of Modules ..................................... 15

Section 12

Trouble Shooting ................................................................ 17

Summary of Contents for SEC-40BRM-230

























Search results

Summary of Contents for SEC-40BRM-230

Reviews:

Related manuals for SEC-40BRM-230

Brands by name

Popular brands

Samlexpower SEC-40BRM-230, Owner'S Manual

Search results

Summary of Contents for SEC-40BRM-230

Reviews:

Related manuals for SEC-40BRM-230

Brands by name

Popular brands