background image

9

Member of Exel group

DRT7159 

B - 2023/03

1.4. Simplified analysis of potential ignition sources according to EN 80079-36

1.5. Precautions for Use

This document contains information that all operators should be aware of and understand before using the carts 

Inocart

.

 

This information highlights situations that could result in serious damage and indicates the precautions that 

should be taken to avoid them.

 

Before any use of the Inobox control module, check that all operators:

 

• have previously be trained by the compagny 

Sames

, or by their distributors registered by them for 

this purpose.

• have read and understood the user manual and all rules for installation and operation, as laid out 

below.

It is the responsibility of the operators’ workshop manager to ensure these two points and it is also his 

responsibility to make sure that all operators have read and understood the user 

 

manuals for any peripheral electrical equipment present in the powdering area.

 

 

 

1.6. Warnings

 

It is imperative that anyone wearing a pacemaker does not use the equipment and does not 

enter the projection area. 

 

 

High voltage can cause the pacemaker to malfunction.

 

 

This equipment may be hazardous if it is not used, disassembled and reassembled in 

accordance with the rules indicated in this manual and in any applicable European Standard or 

national safety regulations.

 

 

This equipment is intended for spraying powder paint only.

Risk of ignition

Measures applied to prevent the source of 

ignition from becoming effective

Potential source of 
ignition

Description / Main cause (What are the conditions 
causing the risk of ignition)

Description of the measure applied

Hot surface

Vibrator heating in vibrating table version

Maximum vibrator surface temperature of 
100°C

Static electricity

Internal electrostatic discharge in powder hose

Antistatic hose 

Electrostatic discharge on the cart

Equipotentiality of the metal parts + earthing

Electrostatic discharge on the tank for the tank 
version

Equipotentiality of the metal parts + earthing

Summary of Contents for Inocart VT




































































Reviews: