background image

Instructions - Parts List

RAZOR

®

 Siphon 

Feed Gun

II 2 G

TI8222A

312106F

ENG

A premier gun for the automotive refinish market for use with thin to medium viscosity 
materials (14-20 seconds Zahn #2 cup). If spraying heavier materials, use a pressure or 
gravity feed spray gun.

Includes HVLP, Compliant, and Conventional Series.

See page 2 for List of Models and maximum working pressures.
See page 10 for Parts.

This manual is available in the following languages.

Contents

Models  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Repair   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Technical Data   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Accessories   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Parts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Graco Standard Warranty   . . . . . . . . . . . . . . . . . . . 12

Graco Information   . . . . . . . . . . . . . . . . . . . . . . . . . 12

Important Safety Instructions

Read all warnings and instructions in this 
manual. Save these instructions.

English

312106

Spanish

312107

French

312108

German

312109

Italian

312110

Summary of Contents for RAZOR 2288588













Reviews: