background image

 

Instruction manual 

Rear - front and rear flail mowers 

MIDO, GRINO, VINO, MAMUT, RIO

 

  

8

 - 

4.

 

SAFETY PRECAUTIONS 

4.1. Safety rules and regulations 

 

Front or rear axis of the tractor should be balanced to enable its steering. If necessary, use front 
or rear wheel weights. 

 

In order to keep steering conditions, make sure that impact on the front axis is at least 20% of 
the complete impact on the tractor. 

 

Any  operation  with  the  hydraulic  lift  lever  should  be  done  from  the  operator's  seat;  never 
operate the lever from outside of the tractor. 

 

For tractors equipped with EHR, control with hydraulic lift is done with a button located outside 
the tractor's cabin. When operating, please exercise particular caution. 

 

When  mounting  the  mower  on  a  tractor,  risk  of  wounding  is  likely.  It  is  recommended  that 
operator wears protective gloves. 

 

Do  not  operate  without  safety  guards.  Neither  operation  with  damaged  nor  raised  guard  is 
allowed (risk of stones, etc. being thrown out). Damaged safety curtain should be replaced. 

 

Please make sure that no unauthorized personnel remains within the danger area of at least 164 
ft (50m). Keep particular caution when operating near roads and in stony areas. 

 

Perform  any  maintenance  and  adjustment  work  only  when  the  drive  is  disconnected  and  rotor 
has stopped completely. 

 

When  driving  on  public  roads  always  comply  with  local  traffic  regulations,  especially  on  the 
warning lights.

 

 

CAUTION!

 

Make sure to perform any service and repair operations with the tractor drive 
shut off and after all rotating parts have stopped completely. 

 

WARNING: 

Keep children away from the mower when operating and idle. 

 

 

 

Check bolts and other fasteners regularly. Do not operate with damaged or worn fasteners. 

 

Do not leave a running tractor without supervision. Before leaving the tractor turn off the engine 
and remove the ignition key 

 

If any break in the machine operation occurs, turn off the drive 

 

Tractor cooperating with the mower should be equipped with a driver's cabin 

 

Mower should not be operated when the tractor-mower aggregate is not well balanced 

 

Never start the mower if any people or animals are around the mower 

 

Always follow safety labels describing hazards, and warning signs placed on the machine 

 

Before  starting  the  tractor  make  sure  that  each  drive  is  disconnected  and  control  levers  for 
hydraulics are in neutral position 

 

Do not drive the mower backwards when operating 

 

Never get onto the mower 

 

Never stand between the tractor and the mower, unless the tractor-mower aggregate is protected 
against moving with the tractor's parking brake 

 

Any inspections and adjustments may be conducted only when the mower is disconnected from 
the tractor and on the ground 

 

For  repairs  or  adjustments  to  be  done  under  the  mower  make  sure  to  secure  it  against  falling 
using a proper support 

 

If any part of the mower needs to be replaced, use only original spare parts according to spare 
part list 

 

Pay particular attention to PTO shaft guards and mower and tractor spline shaft guards. Never 
operate with damaged guards 

 

Inspect hydraulic hoses on regular basis and if any damage is found or their service life expires, 
replace them. Service life for a hydraulic hose should be no longer than 5 years.  

Summary of Contents for MIDO 140


































Reviews: