13
SettINg tHe cUrreNt tIme
When the player is turned off, press the
clk
button to start setting the current time.
The hour will start the flash, and you can change the value with the
and
buttons. If you press
clk
again you can set the value for minutes in a similar way; pressing
clk
a third time leaves this menu. The current time is shown on the display when the player is turned off
• The clock works in 24-hour cycles.
• If you do not press any button for 3 seconds, the display reverts to the original mode showing the current time.
coNNectINg aN eXterNal amPlIFIer
The preamp output at the back of the head unit allows you to connect an external amplifier or active sub box with a low input level to the player.
This way you can achieve even better volume and sound quality.
White RCA socket: left channel output; Red RCA socket: right channel output.
warNINgS
• Before starting to use the player, read these instructions carefully, then keep them in an accessible place for future reference.
• If needed, consult a technician before installing the player to avoid damaging the product or your vehicle.
• While underway, do not do anything that distracts your attention from driving. Manipulating the player while driving can result in accidents. If needed, stop the car while manipulating
the player.
• Do not listen to the player too loud. Set a volume that allows you hear external sounds while driving. Extreme volumes can also cause permanent damage to your ears.
• Spend as little time as possible watching the display. Doing so can distract your attention from the road, and result in accidents.
• Do not disassemble or tamper with the player, as that can cause fire, accidents, or electric shock. Incorrect use or installation renders the warranty void.
• Only for use in cars with a 12 V battery and a negative ground. Using the player for any other purpose can result in electric shock, damage, or fire. The player was designed
exclusively for use in vehicles.
• Always use melting fuses with the proper values. When replacing a fuse, make sure that the new fuse has the same nominal value as the one you are replacing. Using a different
fuse can cause fire or damage.
• Do not block the player’s cooling vents, as that can cause its circuits to overheat, resulting in fire. Install the player properly to ensure adequate ventilation. The air vents around
the edge must be left free.
• Make sure to connect the player correctly. Incorrect connections can result in fire or other damage.
• Before connecting/installing the player disconnect the negative pole of the car’s battery. Doing so helps you prevent electric shock or short circuits.
• While installing the player never cut through cables or damage their insulation. Doing so can result in short circuit and fire.
• Before drilling holes or inserting screws into your vehicle’s body make sure you do not damage tubes or electric wires on the other side of the cover.
• Do not connect to any electric systems of your vehicle that operate steering, brakes, or any other safety function. Doing so can result in loss of control over the vehicle, and can
cause fire.
• Do not install the player or its accessories in a location where they can prevent you from controlling the vehicle safely, e.g., between the steering wheel and the gear shift.
• Make sure that wires do not coil around neighboring objects. Arrange cables and wires in a way that does not hinder you in driving. Wires that interfere with your movement or hang
over the gear shift, the brake etc. can be extremely dangerous. (E.g., the connection cable of a media player connected to the USB port.)
• In case of any malfunction, turn of the player immediately, and consult your distributor. Many malfunctions are very easy to spot (e.g., no sound, bad smell, smoke, an external
object inside the product etc.).
• Make sure that no external objects get into the USB socket or the memory card slot, as these can cause fatal damage.
• When leading the connection cables make sure that their insulation does not get damaged by any sharp metal objects nearby.
• Do not connect any cables when the device is working. Never turn on the system with the volume at the maximum level. The pop or other noise spike which can be heard when
switching on can cause irreparable damage to the speakers immediately.
• The warranty is not applicable to damage caused by irresponsible or improper installation or use.
PrecaUtIoNS
cleaNINg
Use a soft, dry cloth and a brush for regular cleaning. To remove stronger stains, wet the cloth slightly with water. Avoid scratching the display’s surface; never wipe the display when
it is dry, and do not use a coarse cloth to clean the display. Do not use detergents. Make sure no liquid gets inside the product or onto the connectors!
temPeratUre
Before turning on the player make sure that the temperature inside the car is between -10°C and +55°C, as the product is only guaranteed to operate properly within this temperature
range. Extreme weather conditions can damage the product.
FINDINg tHe rIgHt locatIoN aND INStallatIoN
When installing the product, make sure it will not be exposed to any of the following:
- direct sunlight or heat (e.g. from the heating system)
- wetness, high humidity
- a significant amount of dust
- strong vibration
USINg tHe USb/SD coNNector
• You can connect a USB stick (“pen drive”), MP3 audio player, MP4 media player or similar devices to the player’s USB port. The memory card slot can host SD/SDHC/MMC cards.
Supported file format for playback: MP3 audio files.
• In some cases, external USB/SD devices may not be guaranteed to work properly. Manufacturers occasionally change the internal design of their products (e.g., replace a chip
used inside), which does not change the product’s main technical parameters, but it can affect the operation of devices designed for a similar but previous generation product. It is
therefore possible that even products of the exact same type yield different results. Do not use a USB hub; extension cords are allowed. Do not connect both a USB stick and an
SD card at the same time to the player.
