SAL Nationwide Pty Ltd 40 Biloela Street Ltd, Villawood NSW 2163 ABN 45 144 501 020
Copyright SAL V4 MAR/2018 |
8
. Specific introduction & installation procedures
:
(PIXIE switch device) This device can pair with one PIXIE smart switch. Once set, pressing the button once will turn the
switch on and then turn off the switch after the set duration (once).
(PIXIE dimmer device) This device can pair with one PIXIE smart dimmer. Once set, pressing the button once will turn on
the dimmer, and then turn off the dimmer after the set duration (once).
(PIXIE LED strip) This device can pair with one PIXIE smart strip kit. Once set, pressing the button once will turn on the strip
kit, and then turn off the strip kit after a set duration (once). It can also pair with a group of PIXE RGB strip kits eg: once
pressed, it will turn on all strip kits to a set duration and then turn off the strip kits after the set duration (once)
NOTES / FEATURES:
WIRING
1.
Timer duration can be programmed manually and via the PIXIE App. When
programming manually, only hourly timer functions can be set, and the period is
from 1 hr to max 24 hrs. When programming via the App, the available timer range
is from 1 minute to 24 hours.
2.
Multiway control - When pair multiple STC/BT devices with the same PIXIE device or
the same group of PIXIE devices, multiway timer control is achieved
3.
Programming Timer Duration, delay time - Programming is only available when the
STC/BT is not in timer mode. Please set up the timer duration before pairing STC/BT
with designated PIXIE device or group.
4.
Turning off the LED indicator - Quickly press the button 7 times to turn off the LED
indicator.
5.
Reset to factory - Quickly press the button 9 times to reset to factory. The LED indicator
will flash 3 times and then stay lit for 2 seconds if successful.
6.
A quick press of the button will turn the paired PIXIE device/group ON, the LED indicator will flash for 5 seconds
indicating the timer mode is activated.
7.
The LED indicator will blink every 3 seconds to indicate timer mode is in operation.
8.
In the last 1 minute of timer mode, the LED indicator will flash quickly indicating imminent time out.
9.
During the operation, a quick press on the button will cancel the timer and turn the PIXIE device/group OFF.
10.
During the operation, quickly pressing the button twice will reset the timer mode and the timer will count again.
11.
Pushing and holding the button for 3 seconds (release when the LED indicator turns off) manually overrides to
turn ON or turn OFF the PIXIE device/group in an untimed manner. The LED indicator will remain on whilst in the
ON status.
Manual setting (Timer duration set up):
To enter the programming mode, push and hold the button down for 10
seconds, the LED indicator will start to slowly cycle
indicating the programming mode has launched.
To program, press the button between 1 and 24 times according to the desired delay in hours. For example, 8 presses
will result in a delay of 8 hours. Pressed more than 24 times will result in a delay time of 24 hours being stored.
Programming mode expires 10 seconds after the last button press. At this time the new delay time is stored in memory.
Note: if no button presses were detected, the delay time will be unchanged.
Manual setting (Pairing): NOTE: the device will only operate with a SAL PIXIE device.
(Switch or dimming devices):
Launch the pairing mode for the PIXIE device eg: SDD350BT or SWL350BT by quickly
pressing the button of SDD350BT or SWL350BT 4 times to enter the pairing mode. When the LED indicator of SDD350BT or
SWL350BT continually flashes in blue and white, the pairing mode has launched.
Quickly press the button of the STC/BT 4 times within 30 seconds. When the LED indicator of the STC/BT flashes twice and
then remains lit for 2 seconds, pairing is successful. NOTE: If the paired PIXIE device changes HOME setup in the PIXIE app
or reset to factory, the pairing process will need to be repeated.
(LED strip devices):
Launch the pairing mode for the PIXIE RGB LED Strip Kit and PIXIE White LED Strip Kit - Aim the remote
control supplied to the controller, then long press the
“ON” button for 3 seconds
. When the LED strip starts to flash, the
pairing mode has launched.