background image

1.2.2 Explanations of Symbols

1.2.3 Safety Instructions

Symbol

Dangerous electrical voltage

This device is directly connected to public grid, thus all work to the inve er shall only be 
carried out by quali ed personnel.

Danger to life due to high electrical voltage!

Notice, danger! 

This is directly connected with electricity generators and public grid.

Danger of hot su ace

An error has occurred

Please go to Chapter 9 “Troubleshooting” to remedy the error.

This device SHALL NOT be disposed of in residential waste

Please go to Chapter 8 “Recycling and Disposal” for proper treatments.

Without Transformer

This inve er does not use transformer for the isolation function.

CE Mark

RCM Mark

No unauthorized pe orations or modi cations

Description

There might be residual currents in inve er because of large capacitors. Wait 5 MINUTES 
before you remove the front lid.

The components inside the inve er will release a lot of heat during operation. Do not 
touch metal plate housing during operating.

With CE mark & the inve er ful lls the basic requirements of the Guideline Governing 
Low-Voltage and Electro-magnetic Compatibility.

Equipment meets safety and other requirements as required by electrical safety laws/
regulations in Australian and New Zealand.

Any unauthorized pe orations or modi cations are strictly forbidden, if any defect or 
damage (device/person) occurred, SAJ shall not take any responsibility for it.

DANGER

· There is possibility of dying due to electrical shock and high voltage.
· Do not touch the operating component of the inve er; it might result in burning or death.
· To prevent risk of electric shock during installation and maintenance, please make sure that all AC and DC terminals 
   are plugged out.
· Do not touch the su ace of the inve er while the housing is wet, otherwise, it might cause electrical shock.
· Do not stay close to the inve er while there are severe weather conditions including storm, lighting, etc.
· Before opening the housing, the SAJ inve er must be disconnected from the grid and PV generator; you must wait for 
   at least  ve minutes to let the energy storage capacitors completely discharged after disconnecting from power source.

· The installation, se ice, recycling and disposal of the inve ers must be pe ormed by quali ed personnel only in 
   compliance with national and local standards and regulations.
· Any unauthorized actions including modi cation of product functionality of any form may cause lethal hazard to the 
   operator, third pa ies, the units or their prope y. SAJ is not responsible for the loss and these warranty claims.
· The SAJ inve er must only be operated with PV generator. Do not connect any other source of energy to the SAJ inve er.
· Be sure that the PV generator and inve er are well grounded in order to protect prope ies and persons.

WARNING

· The inve er will become hot during operation. Please do not touch the heat sink or peripheral su ace during or 
   sho ly after operation.
· Risk of damage due to improper modi cations.

CAUTION

· Public utility only.
· The inve er is designed to feed AC power directly to the public utility power grid; do not connect AC output of the 
   inve er to any private AC equipment.

NOTICE

Risk  of  electric  shock!  Only 
authorized  personnel  are  allowed 
to do disassembly, modi cation or 
maintenance. Any resulting  defect 
or  damage  (device/person)  is  not 
coverde by SAJ guaranty.

ATTENTION

!

03

04

ROOFTOP SOLAR INVERTER 

INSTRUCTION MANUAL 

Summary of Contents for H2 Series























Reviews: