background image

 

                                                                       

  B1

 Series                     

 

 

 
 

 

- 6 -

 

 

Potential danger of damaged battery: 

Chemical  Hazard:  Despite  of  its  strict  and  professional  protection  design 

against  any  hazard  results,  rupture  of  battery  shall  may  still  occur  due  to 

mechanical  damage,  internal  pressure  and  etc.,  and  may  result  in  a  leakage  of 

battery electrolyte. The electrolyte is corrosive and flammable. When there is fire, 

the  toxic  gases  produced  will  cause  skin  and  eyes  irritation,  and  discomfort  after 

inhalation. Therefore:   

1) Do not open damaged batteries; 

2) Do not damage the battery again (shock, fall, trample, etc.); 

3)  Keep  damaged  batteries  away  from  water  (except  to  prevent  an  energy 

storage system from catching fire); 

4) Do not expose the damaged battery to the sun to prevent internal heating 

of the battery. 

 

Electrical  hazard:  The  reason  of  fire  and  explosion  accidents  in  lithium 

batteries is battery explosion. Here are the main factors of battery explosion:   

1) Short circuit of battery. Short circuit will generate high heat inside battery, 

resulting  in  partial  electrolyte  gasification,  which  will  stretches  the  battery  shell. 

The temperature reaching ignition point of internal material will lead to explosive 

combustion. 

2)  Overcharge  of  battery.  Overcharge  of  battery  may  precipitate  lithium 

metal. If the shell is broken, it will come into direct contact with the air, resulting 

in combustion. The electrolyte will be ignited at the same time, resulting in strong 

flame, rapid expansion of gas and explosion. 

 

Summary of Contents for B1 Series





























Reviews: