background image

S U P P O R T   E Q U I P M E N T

3

Engine Parts 

Identification

It is important to be able to identify 
the parts of your Saito engines. In the 
back of this manual you will find an 
exploded view of Saito twin-cylinder 
engines, as well as a chart which 
includes part numbers and 
descriptions. This will assist you in 
easily and rapidly identifying the 
respective parts of your Saito engine.

Support Equipment

The following items, which are not 
included with your Saito engine, are 
necessary in order to operate the 
model engine:

1.

Fuel. For maximum protection 

and longevity of Saito engines, Saito 
recommends a fuel containing 20% oil 
and 10-15% nitro methane. If this blend 
is not readily available, the next best 
selection is a high quality 2-cycle glow 
fuel, such as Cool Power, K&B, Power 
Master, etc. Fuels composed entirely of 
castor oil are not recommended. Use of 
such fuels will void the warranty.

2.

Propeller. Refer to the Propeller 

Selection Chart, located on page 18, 
to determine the best initial propeller 
for your particular application.

3. Glow Plug Battery. 

Your glow 

plug may be properly heated by several 
different sources. The Hangar 9 Power 
Panel (HAN106), when accompanied 
by a 12V sealed lead acid battery 
(HAN102) and a glow plug locking 
socket (HAN120), is an ideal source of 
heat for your glow plug.A 
conventional 1.5V heavy-duty dry cell 
battery with a glow plug locking 
socket (HAN120) or alligator clips can 
also be used. Additionally, there are 
several very good glow-starters (nickel 
cadmium powered glow plug ignitors) 
which work well. (HAN7101).

4. Glow Plug Wrench.

 A glow plug 

wrench is used to remove and tighten 
glow plugs. The Hangar 9 Long 
Reach Plug Wrench (HAN2510) is an 
excellent wrench to utilize as a longer 
shaft may be necessary to access the 
glow plug. This depends mostly upon 
engine installation.

5. Manual or Electric Starter.

 For 

manual starts, a“start stick”(HAN113) 
is highly recommended. never use your 
fingers to start any model engine, as 
doing so invites injury. There are a 
variety of electric starters on the 
market. The Hangar 9 PowerPro-HD 
12V Starter (HAN102) will work 
perfectly on all of the twin-cylinder 
Saito engines.

Summary of Contents for FA-60T



























Reviews: