background image

02/23/2015 

Sailfish 270 WAC Owner’s Manual  |  sailfishboats.com 

15

     

VSR Battery System – “The Smart Battery Switch”

The VSR, or Voltage Sensitive Relay, is a very handy little box 

that solves a load of traditional charging problems on marine 

electrical systems. It essentially serves as a smart battery switch 

deciding automatically when either one or two batteries are 

charged – or discharged. It works great on almost any boat with 

multiple batteries – and eliminates all of the guesswork that used 

to come with manual battery switches.

What a VSR does

The VSR is installed between two batteries. Many People are 

surprised to learn that it is NOT connected to either the alternator 

or charger output wires! Its setup is much more clever.

 

It either battery goes above 13.7 volts (due to either alternator or 

charger output), the VSR connects both batteries together. Both 

batteries are now charging – without the boat ever having to throw 

a switch.

Alternately, when the system voltage drops back below 12.6 

volts, i.e., no more charging, the relay opens and the batteries 

are separate. This means that both batteries now discharge 

independently.

How a VSR changes real

 

world boating 

Let’s say that a fishing boat has a two battery setup. As is often 

the case, one of the batteries is dedicated to an important job – 

starting the engine. The other battery is used for other operations.

As the fisherman runs the boat from hole to hole, the engine 

alternator elevates the voltage to the cranking battery above 13.7 

volts. This triggers the VSR to automatically connect the starting 

battery and house battery together. Both are now charging.

Upon reaching his destination, the boater kills the engine – and, 

the alternator output – and begins trolling. Because of the lowered 

voltage, the VSR now disconnects the batteries. Because he is 

now discharging only one battery, our fisherman is going to have 

starting power when he needs it later – no matter how long he 

uses the trolling motor and depletes that trolling battery.Once 

underway again, the alternator power causes the VSR to recon-

nect the batteries and begins replenishing the trolling battery.

Back home, the fisherman powers up his onboard battery charger, 

this increased voltage causes the VSR to once again link the 

batteries. This means that even a single output battery charger 

would now be charging both batteries!

Summary of Contents for 240 WAC






































Reviews: