manualshive.com logo in svg

Sagetech MXS, Installation Manual

Share
Download
Sagetech MXS Installation Manual Download Page 3

MXS System Description and Installation Manual 

UM06945

 

© Sagetech Avionics 2022 Proprietary Confidential 

Page 3 of 56 

6.0

 

Electrical Characteristics .................................................................................................... 27

 

6.1

 

Main Connector .............................................................................................................. 27

 

7.0

 

Power up Process ............................................................................................................... 32

 

7.1

 

Setup Equipment ............................................................................................................ 32

 

7.2

 

Power Up The MXS ......................................................................................................... 32

 

7.3

 

Check For the Boot Loader Message .............................................................................. 33

 

7.4

 

Send Installation Message.............................................................................................. 33

 

7.5

 

Send GPS Information .................................................................................................... 37

 

7.6

 

Send Operating message ................................................................................................ 39

 

7.7

 

Send Flight ID.................................................................................................................. 42

 

7.8

 

ADS-B In .......................................................................................................................... 43

 

7.9

 

Monitor Health and Status ............................................................................................. 44

 

7.10

 

Health Monitoring and Built-in-Test (BIT) ...................................................................... 45

 

7.11

 

System Health and Status Overview .............................................................................. 45

 

7.12

 

Status Response Messages ............................................................................................ 46

 

8.0

 

Revision History ................................................................................................................. 52

 

9.0

 

Appendix A 

–

Shielded Cable Assembly Construction ........................................................ 53

 

 

 

 

Summary of Contents for MXS

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands