background image

SDC-620 Multiple door controller 

 

 

 
Copyright© 2016 

– Saflec Systems (Pty) Ltd. 

http://www.saflecsystems.co.za 

The configuration and diagnostics OLED panel 

The configuration panel has been added to simplify some configuration tasks for the installer. It 
has an OLED screen and 5 buttons for control. The Left and Right buttons are used to change 
pages or move to another field within a configuration page when configuring. The Up and Down 
buttons are used on all number fields to increase or decrease the value and the Enter button is 
used to apply changes or to activate a command. 
 
Once the controller is given power the panel will be active. If the screen is blank, it will be in 
screen-saving mode. Tapping any button will awaken the screen and allow you to configure the 
device. 
 

 

 
 
 
 
 
 
 

Figure 3 

The configuration and diagnostics OLED panel. 

 
Various tasks can be performed from the menu system, however only a few tasks will be covered 
in this guide. 
 

NOTE:

 Some functions are password protected and the password must be entered before being 

given access to that function. The default 

password is ‘1234’ – but this can be changed from the 

web interface. When the password is requested you would use the Up and Down buttons to 
change the letter or number shown until it is correct, then Right to move to the next character. This 
process would repeat until the entire password has been entered, then the Enter button is pressed 
to confirm. 
 

 

Summary of Contents for SDC-620













Reviews: