background image

  

225 Wilshire Ave SW, Concord NC, 28025

  

Phone: 800-230-0319

  

Email: [email protected]

  

Web: safewaze.com

 

 Fax: 704-262-9051

I

I

I

I

I

Hole Diameter

5/8”

Minimum Thickness

1/4”

3”

(A) Min Dis

t. from any 

edge

INST

ALL

INST

ALL

INST

ALL

INST

ALL

INSTALL

INSTALL

INSTALL

ANSI Z359.14, ANSI A10.32 

OSHA 1910.66, OSHA 1926.502

          

020097

INSTALL

INSTALL

INSTALLATION

ANCHOR COMPONENTS

WARNING

 

    

   

•  Users should consult with their doctor to verify ability to safely absorb the forces of a fall arrest event.  

Fitness level, age, and other health conditions can greatly affect an individuals ability to withstand fall 

arrest forces. Women who are pregnant, individuals considered minors must not use any Safewaze 

equipment. 

•  Never alter any part of an anchor or add/remove components.  Safewaze shall not be held 

responsible for injury or death due to tampering.

•  Anchors that are exposed to fall arrest forces MUST be IMMEDIATELY removed from service and 

destroyed.  

•  Failure to follow these instructions and warnings could result in serious injury or death in the event 

of a fall.

•  A preplanned rescue procedure in the event of a fall is required.  The rescue plan must be specific to 

the project.  The rescue plan must allow for employees to rescue themselves, or to be promptly rescued 

by alternative means. 

•  Harnesses or connectors selected for use with any Safewaze anchor must be compatible in size and 

configuration. User must ensure compatibility of snap hooks, carabiners and other connectors.  Any 

connection which could allow disengagement must be eliminated. Snap hooks and carabiners must be 

self locking and self closing and must never be hooked to each other. 

•  A Competent Person must conduct an analysis of the workplace and anticipate where workers will be 

conducting their duties, the route they will take to reach their work, and the existing and potential fall 

hazards they may be exposed to.  The Competent Person must choose the fall protection equipment 

to be utilized.  

•  Do not misuse equipment.

•  Equipment designated for fall protection must never be used to lift, hang, support or hoist tools or 

equipment unless specifically certified for such use.    

•  Safewaze Anchors shall be inspected prior to each use by the user, and at least annually  by a 

Competent Person other than the user.  Annual inspections shall be documented.  Severity of conditions 

during use may necessitate increased frequency of documented inspections.  

•  Anchors that fail inspection MUST be removed from service.

•  Prior to each use, inspect the anchor for deficiencies or damage, including, but not limited to, sharp 

edges, rough edges, deformations, corrosion, pits, burrs, chemical exposure, extreme heat exposure, 

kinked, bird nested, or otherwise damaged cable, and damaged, missing or illegible labels. If any 

deficiencies or defects are found, the anchor must IMMEDIATELY be removed from service.

•  The anchor must be inspected at least annually by a Competent Person other than the user.  

Competent person inspections must be recorded in the inspection log included in this manual and 

on the inspection grid label on the anchor. 

INSPECTION

MAINTENANCE & STORAGE

WARRANTY

Anchor can be cleaned with water and mild soap if necessary.  User should remove all dirt, possible 

corrosives, and contaminants from the anchor prior to, and after each use.  Never use any type of 

corrosive substance to clean the anchor.  

Excess water should be blown out with compressed air.  Hardware can be wiped off with a clean, dry 

cloth.

When not in use, store the anchor in a cool dry area where it will not be exposed to extreme light, 

extreme heat, excessive moisture, or possibly corrosive chemicals or materials.   

Safewaze warrants its products are free from defects in materials and construction under normal use 

and service.  Liability is not accepted for abuse, modification, improper use, destructive activity and 

contaminated exposure. 

INSPECTION LOG

Date

Inspection Items 

Noted

Corrective Action

Initials

LABELS

1. The 021-4046 can be installed both vertically and horizontally.  The installation process is the            

    same for both methods.

2. The work location should be free of debris, and other materials or equipment that could  

         

     interfere with the proper operation of this equipment.

3. Inspect the steel to which the anchor will be attached.  User should inspect for the following    

    hazards.  These hazards include, but are not limited to, excessive corrosion, cracks, severe       

    rust, excessive paint, spray applied fireproofing, electrical hazards, etc...  

4. Installation requires steel 1/4” thick or greater. Installation location must be a minimum of 3” from any  

    edge.  Drill a 5/8” diameter hole completely through the steel (See Table 1 and Figure 6).

5. Once hole is drilled and cleared of burrs, metal shavings, or other debris,  insert the threaded bolt  

    portion of the anchor through the drilled hole (See Figures 8 and 9, Dwgs.1-2). 

 

6. Install steel washer and nut onto the bolt portion of the anchor (See Figure 8 and 9, Dwgs. 3-4) and     

    torque to 75-90 ft-lbs. (100-120Nm). 

7. PFAS connecting device can now be connected to the 021-4046 (See Figures 8 and 9, Dwg. 5).

FIGURE 5 - ANCHOR COMPONENTS

FIGURE 8 - VERTICAL INSTALLATION

FIGURE 9 - HORIZONTAL INSTALLATION

FIGURE 6 - REQUIRED INSTALLATION DIMENSIONS

FIGURE 7 - LOAD CONDITIONS DIAGRAM

TABLE 1 - INSTALLATION

B

C

D

A

Dwg. 1

Dwg. 1

Dwg. 2

Dwg. 3

Dwg. 4

Dwg. 5

Dwg. 2

Dwg. 3

Dwg. 4

Dwg. 5

Anchor Components

A

Fall Protection Connection Point

B

Stainless Steel Swivel Anchor Bolt

C

Stainless Steel Swivel Anchor Bolt Head

D

Stainless Steel Washer

Hole Dimensions

Steel

5/8” Diameter

3” Min Distance from any edge

Steel

X

WARNING:  

This equipment must be inspected prior to each 

use.  Any unit that has been exposed to fall arrest forces must 

be removed from service.  Avoid contact with sharp edges and 

abrasive surfaces.  Only use compatible connections.  Do not 

subject this equipment to physical hazards that include thermal, 

electrical, and chemical sources.  User must read, understand and 

follow all manufacturer’s instructions included with this unit at the 

time of shipment.  Failure to follow these and any of the 

manufacturer’s instructions may result in serious injury or death. 

Part #: 021-4046 

5K Swivel Stainless 

Steel Anchor & Bolt

225 Wilshire Ave SW Concord, NC 28025

J

F M

M

Y

M

A

A

J J

S O N D

Inspection Log 

INSTALL

www.safewaze.com

Materials:  

Stainless Steel

MBS:  

5,000lbs / 22.2kN 

Weight Capacity:  

ANSI: 130-310lbs (140.6kg)

OSHA: 420 lbs (190.5kg)

Meets:

OSHA 1910.66, 1926.502 

ANSI A10.32, Z359.18 Type A

Reviews: