background image

Safety Instructions 

Thank you for purchasing Safety View backup camera monitor DVR  

model SVM-M718-4DVR.  

Please read through this  

manual before installing and operating this equipment.  

CAUTIONS: 

 

 Please read the operating manual carefully and keep the man-
ual in the cab for future reference  
 Please do not install this monitor where it can obstruct the op-
erators' safe view.  
 Do not use a water hose or pressure washer to clean this 
monitor. (If you intend to subject this monitor to moisture. Only 
use soft damp cloth to clean the display and housing. Do not use 
alcohol or other chemical cleaners.  
 Storage temperature is –30c~70C  
 Do Not focus on this monitor while driving.  
 Do Not adjust buttons on front monitor panel while driving. 
Distractive driving laws are in effect in most jurisdictions.  
 Always look around you, through the windows, in the mirrors 
and on the monitor before placing your equipment in reverse. If 
you still have blind spots around your machine, you will need to 
add additional cameras to this 4 channel DVR monitor or use a 
trained signaller. By Law, Do Not operate your machine or truck 
in reverse if there is blind spots.  
 Do not operate your machine or truck if the monitor/camera 
and or mirrors are not functioning.  
 Only install this monitor on 9 ~ 36 Volt DC equipment  

 

Notes 

Summary of Contents for SVM-M718-4DVR









Reviews: