background image

25

C-8 

Removing Seat Pad for Cleaning

You must remove the harness system to remove the 
pad. See section C-7.

Release the Elastic Straps     
(on select models) 

Release the elastic straps on the 
back and under side of the child 
restraint.

NOTE:

 The positions of the elastic 

straps may vary by model.

1.

 

2.

 

Lower Harness Guides

A

Remove Lower Harness 
Guides from Bottom of 
Seat

From the back, in the fully 
upright position, locate the 
lower harness guides that are 
between the bottom of the 
seat and base 

(A)

.

Insert a flat head screw driver 
into the hole in the base where 
the lower harness guide is 
located.

a.

 

Place the screw driver’s tip 
between shell and lower harness 
guide, then twist the screw driver 
while pulling the harness guide 
from the front. Repeat for other 
side.

b.

 

26

C. Basic Use

Remove Seat Pad 

Adjust the headrest to the lowest 
position. Pull pad off the top of 
seat and around headrest pad.  
Pull the pad off the bottom of shell 
and remove the pad.

3.

 

4.

 

Upper Harness Guides

Remove Upper Harness 
Guides

From the back of child 
restraint, pinch harness 
guide ends together or use 
a screwdriver to press in on 
harness guide edge as shown. 
With the other hand, from 
the front of the restraint, pull 
the harness guides out of the 
headrest.

Remove headrest pad.

Install Pad

Replace seat pad by reversing order for your particular model.
Slip headrest pad on and replace the upper harness guides. 
Starting from bottom of child restraint, slip pad on shell; pull 
harness adjustment strap through pad. Make sure pad is 
behind headrest and backrest. 
Install lower harness guides.
Attach all of the elastic straps. 
Install harness system (see section C-9).

Cleaning Pad

Hand wash pad with warm sudsy water, rinse clean and air 
dry. Do not use bleach or use other harsh cleaners. Do not 
dry clean or machine wash.

Harness Straps:

 Spot clean only. Do not machine or hand 

wash.

NOTE:

 

Do not wash the pad while still on the shell. Spot 

clean only if it is not removed.

Do not use this child restraint or booster seat 
without the seat pad. Failure to do this can 
result in serious injury.

4358-6199 Elite Eng.indd   27-28

4358-6199 Elite Eng.indd   27-28

10/11/12   4:11 PM

10/11/12   4:11 PM

Summary of Contents for Alpha Elite 65

































Reviews: