Monitor Set Up
The portable Monitor operates by use of 4 AA alkaline batteries (not included) or the AC Adapter cord included with the 900 MHz In Sight
Hand-Held TV-Video Monitor for AC Monitor power.
REMEMBER:
Use only the AC Adapter included with the 900 MHz In Sight Hand-Held TV-Video Monitor for power.
IMPORTANT NOTES:
• Keep the Monitor out of reach of children.
• Keep the Monitor upright for best reception.
Page 8
Page 9
Installing the Batteries
• Do not submerge any part of TV/Video Monitor in water.
• Remove batteries when stored for long periods of non-use.
• Remove spent batteries promptly.
• Rechargeable batteries may be used but must not be
recharged in the unit.
• Only an adult should charge rechargeable batteries.
• Non-rechargeable batteries must not be recharged.
• DO NOT short circuit supply terminals.
• Insert batteries oriented for the correct polarity
(as shown in battery compartment).
WARNING
STEP 1
Locate the battery compartment door on the back of the TV/Monitor,
and unscrew the battery door in the direction of the arrow to remove as
shown in
Figure A
.
STEP 2
Install 4 AA alkaline batteries (not included) into the battery
compartment as shown. Ensure the (+) and (-) symbols match those
shown in the battery compartment.
STEP 3
Re-align battery door and screw into position.
NOTE:
The TV/Monitor will not work in battery mode if batteries are not
installed properly.
After several hours of continuous use, the Power On/Low Battery LED Light
may turn solid red, indicating that the batteries need to be replaced. Please
follow instructions noted above for the installation of new batteries.
NOTE:
We recommend using household electrical power when possible to
conserve battery power.
A
• Place the Monitor where you can see and hear it.
• To use household power, unwrap and fully extend the AC adapter cord, and plug the jack on the Monitor’s AC Adapter cord into
the AC adapter jack (DC 12V IN) on the side of the Monitor. Then plug the AC adapter into a standard wall outlet. Be certain to
wrap up and secure any excess AC adapter cord.
• Turn the Monitor “ON” by:
-Sliding the Mode Switch to Camera.
-Sliding the channel switch to either A, B or C to match the camera setting.
• Adjust the volume rotary dial to a comfortable sound level.
• If you experience interference switch both the Camera and the Monitor to another channel using the Channel Selector.
To Adjust Brightness and Tint:
• To adjust brightness, press the Brightness / Tint Button on top of the TV-Video Monitor. Then use the TV Tuning / Brightness
Adjuster Buttons to make the picture lighter or darker as needed.
• To adjust tint, press the Brightness / Tint Button twice. Then use the TV Tuning / Brightness Adjuster Buttons to change the
tint as needed.
Monitor Operation
Camera Operation
• Set Camera and Monitor to the same channel.
• Slide the ON/OFF switch on the top of the Camera to the “ON” position.
To Adjust:
• Turn the tilt adjustment knob counter-clockwise just enough to loosen the camera. Move the camera up or down to the
desired position and tighten the camera in place by turning the tilt adjustment knob clockwise. DO NOT OVER TIGHTEN.
• Swivel the camera from side-to-side to obtain desired position.
NOTE:
Camera will turn approximately 180°. Do not attempt to turn it past 180°.
DO NOT
attempt to adjust the small antenna on Camera or Monitor.
Using the Audio Only Feature
The Audio Only feature allows the Monitor to be used without the picture in a sound only mode. To use the Audio Only
feature, set the Mode Switch on the bottom of the Monitor to “AUDIO”. This will allow the Monitor to receive sound only
without picture
.
Using the Monitor as a Television
1. Switch the TV/CAMERA/AUDIO mode to TV.
2. Tune the TV to the desired station using the TV Tuning / Brightness Adjuster Buttons. You can either depress the Buttons quickly to
move through the channels one at a time, or hold the Button down to scroll through the channels.
3. Adjust volume.
4. Adjust the telescoping antenna for best picture.
Note:
The Camera has Night Vision LED’s that allow the Camera to automatically adjust to a
darkened room. The Monitor will automatically switch to black and white reception at this
time, providing you with a clear view of baby at night.