background image

Safetrust Inc. | 

safetrust.com

[email protected]

FCC:

  This  device  complies  with  part  15  of  the  FCC  Rules.  Operation  is

subject  to  the  following  two  conditions:  (1)  This  device  may  not  cause
harmful  interference,  and  (2)  this  device  must  accept  any  interference
received, including interference that may cause undesired operation. 

Canada  Radio  Certification: 

This  device  complies  with  Industry  Canada

license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must  accept  any  interference,  including  interference  that  may  cause
undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux  appareils  radio  exempts  de  licence.  L’exploitation  est  autorisée  aux
deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi,  même  si  le  brouillage  est  susceptible  d’en  compromettre  le
fonctionnement.

CE Marking:

 Safetrust hereby declares that these proximity readers are in

compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.

Summary of Contents for 8845-100

























Reviews: