Safe Fleet TB-100 Hardware Installation Manual Download

Page: 14 / 18

Emergency Lights or Siren Activated Version

TB-100 Bluetooth Transmitter Hardware Installation Guide

P a g e 12

Safe Fleet Mobile-Vision



9.26.2019

Configure your BWX-100 device(s) in DES to support Bluetooth transmission

Log into your DES video management software as an Admin user.

Display the BWX-100’s DVR record.

If there are tabs at the top of the record, click

Video

. Otherwise proceed to the next

step.

Set the

Bluetooth Transmission

field to

Enabled

Enter a unique code in the

Bluetooth ID

field (must be 1 - 12 characters long and

consist of a combination of numbers from 1 - 9 and/or letters from a - f). This will
ensure that your Bluetooth Transmitter only communicates with devices

that share

the same Bluetooth ID.

Click

Close

May include BWX-100s and/or Bluetooth Transmitters. Just remember to assign the same Bluetooth ID to all devices

in the same group!

Sample DVR record with

Fleet Management ON

Sample DVR record with

Fleet Management OFF

Summary of Contents for TB-100


















Search results

Summary of Contents for TB-100

Reviews:

Related manuals for TB-100

Brands by name

Popular brands

Safe Fleet TB-100, Hardware Installation Manual

Search results

Summary of Contents for TB-100

Reviews:

Related manuals for TB-100

Brands by name

Popular brands