Sachtler aktiv10 User Manual Download

Page: 32 / 36

Technical Specification

Height

aktiv10

188 mm (7.4 in)

aktiv10T

188 mm (7.4 in)

Drags (horizontal and vertical)

aktiv10

7 settings plus 0

aktiv10T

7 settings plus 0

Counterbalance steps

aktiv10

15 settings plus 0

aktiv10T

15 settings plus 0

Camera plate sliding range

Touch & Go S - 60 mm (2.4 in)
Sideload S - 120 mm (4.7 in)

Temperature range

-40°C (-40°F) to +60°C (+140°F)

Battery

CR 2032, 3 V

Weight

aktiv10

2.9 kg (6.4 lb)

aktiv10T

3.0 kg (6.6 lb)

Max . Payload

aktiv10

12 kg (26.5 lb)

aktiv10T

12 kg (26.5 lb)

Tilt range

aktiv10

+90° to -70°

aktiv10T

+90° to -70°

Camera fitting

Touch & Go camera plate S (# 0364)
Sideload camera plate (# 0164)

Tripod fitting

100 mm bowl with SpeedSwap base

Pan bar type

Single pan bar DV 75

(# 0992SP)

Diameter 16 / 28 mm (0.63 in / 1. in)
Length 430 mm (16.9 in)

We reserve the right to make changes to the product based on

technical advances.

Summary of Contents for aktiv10





































Search results

Summary of Contents for aktiv10

Reviews:

Related manuals for aktiv10

Brands by name

Popular brands

Sachtler aktiv10, User Manual

Search results

Summary of Contents for aktiv10

Reviews:

Related manuals for aktiv10

Brands by name

Popular brands