SAC MAXI-MIXER 4750, Operator'S Manual

Page: 54 / 60

Page # 54
877 1st Ave. N.W. | Sioux Center, IA 51250 | Toll Free: 1.866.722.1488 | siouxautomation.com
OPERATION
REPLACEMENT PARTS
READ complete manual CAREFULLY
BEFORE attempting operation.
MON900661 EXTENSION KIT
ITEM # QTY PART # DESCRIPTION
1 66 BLT516X114NC 5/16X1-1/4 BOLT
2 2 MON102407 80.06” TOP EXTENSION MOUNT
3 4 MON102408 103.81” TOP EXTENSION MOUNT
4 4 MON102409 CORNER EXTENSION MOUNT
5 614 MON800441 8” 4-PLY BELTING
6 66 NUT516NC 5/16” NUT
7 28 SP14X1TS 1/4X1 SELF TAPPING SCREW
8 66 WSH516FLAT 5/16” FLAT WASHER
9 66 WSH516LOCK 5/16” LOCK WASHER
INSTALLATION INSTRUCTIONS
LAYOUT ANGLE MOUNTS (MON102407 & MON102408) 1.
AS REQUIRED TO ALLOW THE INSIDE EDGE OF BELTING
TO BE FLUSH WITH THE INSIDE EDGE OF MIXING CHAMBER.
SECURE IN PLACE USING SELF-TAPPING SCREWS. (SP14X1TS) 2.
MEASURE AND CUT LENGTHS OF RUBBER EXTENSION 3.
(MON800441) FOR FRONT, REAR, & SIDES.
CLAMP EXTENSION (MON800441) TO ANGLE MOUNTS 4.
(MON102407 & MON102408) & DRILL 3/8" HOLES AS
REQUIRED.
SECURE WITH BOLTS, FLAT, & LOCK WASHERS. 5.
(BLT516X114NC, WSH516FLAT, & WSH516LOCK)
INSTALL CORNER ANGLE MOUNTS (MON102409) WITH SAME 6.
PROCEDURE IN STEPS 4 & 5.
IF WORK MUST BE PERFORMED INSIDE
MIXER, A PROTECTIVE COVER MUST
BE PLACED OVER KNIVES TO AVOID
INJURY OR DEATH.
ALWAYS STOP MIXER AND DISCONNECT
POWER BEFORE LUBRICATING, ADJUSTING
OR SERVICING THIS MACHINE.
WARNING!
7
DETAIL A
SCALE 1 : 4
8
9
1
6
4
2 3
5
A
INSTALLATION INSTRUCTIONS
LAYOUT ANGLE MOUNTS (MON102407 & MON102408) 1.
AS REQUIRED TO ALLOW THE INSIDE EDGE OF BELTING
TO BE FLUSH WITH THE INSIDE EDGE OF MIXING CHAMBER.
SECURE IN PLACE USING SELF-TAPPING SCREWS. (SP14X1TS) 2.
MEASURE AND CUT LENGTHS OF RUBBER EXTENSION 3.
(MON800441) FOR FRONT, REAR, & SIDES.
CLAMP EXTENSION (MON800441) TO ANGLE MOUNTS 4.
(MON102407 & MON102408) & DRILL 3/8" HOLES AS
REQUIRED.
SECURE WITH BOLTS, FLAT, & LOCK WASHERS. 5.
(BLT516X114NC, WSH516FLAT, & WSH516LOCK)
INSTALL CORNER ANGLE MOUNTS (MON102409) WITH SAME 6.
PROCEDURE IN STEPS 4 & 5.
IF WORK MUST BE PERFORMED INSIDE
MIXER, A PROTECTIVE COVER MUST
BE PLACED OVER KNIVES TO AVOID
INJURY OR DEATH.
ALWAYS STOP MIXER AND DISCONNECT
POWER BEFORE LUBRICATING, ADJUSTING
OR SERVICING THIS MACHINE.
WARNING!
7
DETAIL A
SCALE 1 : 4
8
9
1
6
4
2 3
5
A
INSTALLATION INSTRUCTIONS
LAYOUT ANGLE MOUNTS (MON102407 & MON102408) 1.
AS REQUIRED TO ALLOW THE INSIDE EDGE OF BELTING
TO BE FLUSH WITH THE INSIDE EDGE OF MIXING CHAMBER.
SECURE IN PLACE USING SELF-TAPPING SCREWS. (SP14X1TS) 2.
MEASURE AND CUT LENGTHS OF RUBBER EXTENSION 3.
(MON800441) FOR FRONT, REAR, & SIDES.
CLAMP EXTENSION (MON800441) TO ANGLE MOUNTS 4.
(MON102407 & MON102408) & DRILL 3/8" HOLES AS
REQUIRED.
SECURE WITH BOLTS, FLAT, & LOCK WASHERS. 5.
(BLT516X114NC, WSH516FLAT, & WSH516LOCK)
INSTALL CORNER ANGLE MOUNTS (MON102409) WITH SAME 6.
PROCEDURE IN STEPS 4 & 5.
IF WORK MUST BE PERFORMED INSIDE
MIXER, A PROTECTIVE COVER MUST
BE PLACED OVER KNIVES TO AVOID
INJURY OR DEATH.
ALWAYS STOP MIXER AND DISCONNECT
POWER BEFORE LUBRICATING, ADJUSTING
OR SERVICING THIS MACHINE.
WARNING!
7
DETAIL A
SCALE 1 : 4
8
9
1
6
4
2 3
5
A