SAB Heli Division Goblin Helicopter Kraken Manual Download Page 33

Page: 33 / 48

BAG 22

NOTE:

2mm thick tape for the gyro is recommended.

Note:

Tighten by hand.

Overnightening can

damage the dampeners.

Rubber 65 shore

(HC573-S)

Note:

Tighten carefully.

Overnightening can

damage the dampeners.

Flat Head Cap

Screws M3x5mm

(HC132-S)

CF FBL Mount

(H1268-S)

Alu FBL Support

(H1268-S)

FBL/RX PLATE ASSEMBLY

Flat Head Cap

Screws M2.5x8mm

(HC125-S)

Flat Head Cap

Screws M2.5x8mm

(HC125-S)

FBL/RX PLATE

ASSEMBLY

CF RX Mount

(H1399-S)

Socket Head Cap

Screws M3x6mm

(HC044-S)

NOTE:

Use this plate if you

have separate RX.

If you do not want to use the dampeners, you can setup a rigid FBL

mount support using the screws and bushings contained in bag 31-2

Note:

Tighten carefully.

Overnightening can

damage the screws.

Note:

Tighten carefully.

Overnightening can

damage the screws.

Page 32

INSTALLATION FBL/RX

Summary of Contents for Goblin Helicopter Kraken

















































Search results

Summary of Contents for Goblin Helicopter Kraken

Reviews:

Related manuals for Goblin Helicopter Kraken

Brands by name

Popular brands

SAB Heli Division Goblin Helicopter Kraken, Manual

Search results

Summary of Contents for Goblin Helicopter Kraken

Reviews:

Related manuals for Goblin Helicopter Kraken

Brands by name

Popular brands