background image

32 025 690 9

Saab 9-5 5D M06-

50 Align the side trim and connect the CD changer

if fitted. Tighten the screws in the top edge of the
side trim.

51 Refit the cargo guard support (3 screws) and

D-pillar trim.

52 Connect the roof lighting and press the roof

cover into place.

53 Fit new insulation pads.
54 Fit the storage compartment in the floor and the

outer sections of the luggage compartment floor.

55 Fit the scuff plate.
56 Fit the luggage compartment floor.
57 Lift in the cargo guard.
58 Fit the cover between the left-hand rear door

and the backrest and fold back the rear seat
backrests and seat cushions.

59 Check that the system warns against objects in

the rear in the form of a varying number of tones
from SID. The first tone is given when an object
is at a distance of 1.8 metres. The signal then
has a frequency of 2 tones per second, but the
number of tones per second increases the
closer the object becomes to the vehicle and
changes as follows:

·

1.8 - 1.3 m: 2 tones/second

·

1.3 - 0.9 m: 3 tones/second

·

0.9 - 0.3 m: from 5 to 12 tones/second in 
close stages

·

0.3 m: continuous tone

E930A392

53

51

52

54

54

51

55

50

56

56

58

Summary of Contents for 32 025 687










Reviews: