background image

G  

Mounting and Installation

ATTENTION !    

The minimum CO

2   

concentration of outside air in leafy, hardly industrialised areas is approx. 350  ppm (output voltage = 1.75  V

 

with MR = 2000  ppm 

or 0.7 V with MR = 5000  ppm). The

 

gas inter-exchange in the sensor element happens by diffusion.

 

Depending on the changes to the  concentration 

and the flow velocity of the air surrounding the  sensor, the reaction of the device to the change of concentration may take place with a delay.  
It is essential to choose an installation location for the device in which the air stream flows around the sensor. Otherwise the gas exchange may  
be considerably delayed or prevented.

 

Manual calibration of carbon dioxide measurement

Due to the dual-beam measuring system used, automatic calibration is not used. Instead, the output value can be corrected by up to ± 500  ppm by 
means of the corresponding calibration potentiometer if required.

Putting in operation

After switching on the device, a self-test and tempering period follows. This procedure takes 3 to 5 minutes, depending on ambient conditions. During 
this time, the output analog voltage differs from the actual measured value.

AERASGARD

®

 ACO

2

 - SD - TYR 2  

– 

 

On-wall CO

2

 sensors,  Standard 

AERASGARD

®

 ATM - CO

2

 - SD - TYR 2  

– 

 

On-wall  CO

2

 measuring transducers,  Standard

Type ⁄ WG02 

Measuring Range

CO

2

 

Temperature

Output

CO

2

 

Temperature

Item No.

ACO

2

 - SD - TYR2

(switchable)

AC O2- SD -U T Y R2

0...2000 ⁄ 5000 ppm

0 -10 V

1501-7110-1000-300

ATM - CO

2

 - SD - TYR2 

(switchable)

AT M - C O2- SD -U T Y R2

0...2000 ⁄ 5000 ppm

0...+50 °C

0 -10 V

0 -10 V

1501-7112-1000-300

Note: 

This unit 

must not

 be used as safety-relevant device!

Accessories

WS-03

Weather and sun protection, 200 x 180 x 150 mm, stainless steel

7100-0040-6000-000

Summary of Contents for AERASGARD AC02-SD-TYR2

















Reviews: