background image

700-3002-BC 

  

10.18.2017 

 

Seating System - 

The seat is manufactured from rotomolded plastic with a stainless steel frame.  

Armrests are integrated into the seat and are designed for support when transferring onto the seat.  They 
may be rotated up out of the way during transfer.   
 
The seat belt must be used during each use. The footrest is removable and will float upwards to prevent 
damage if the seat is lowered too far. It is recommended that the seat be rinsed off with fresh water 
between each use and cleansed daily with a disinfectant solution of 1:100 dilution of household bleach to 
fresh water and then rinsed with fresh water. In the event of a contamination incident such as patient/user 
excreta - cleanse seat and seatbelt immediately with the above disinfectant solution. Do not use seat or 
seatbelt if it is damaged or becomes worn out.

 

 

 
This lift seat assembly is designed to be used exclusively with S.R. Smith aquatic access lifts.  

 

UNPACKING & ASSEMBLY INSTRUCTIONS 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
REFER TO THE DIAGRAM (page 23) FOR PARTS IDENTIFICATION. 
 
 
 
 
 
 
 

Item 

Part # 

Description 

100-5000A  

LA34 Actuator 

400-7000-BC  4 Button Controller 

120-1920 

Actuator Cable Assembly (not shown) 

1001495-BC  

Battery Pack  

1001530-BC  

Battery Charger (not shown) 

1001600 

Hand Control (not shown) 

160-8530 

Hand Control Hanger (on back of seat) 

120-2100A  

24 VDC Motor 

120-1910 

Motor Cable Assembly (not shown) 

10 

1001498 

Battery Bracket 

11 

310-1000A 

Mast Assembly 

12 

310-1200A 

Actuator Arm Assembly 

13 

310-1300A  

Support Arm Assembly 

14 

160-9520 

Seat Frame Arm 

15 

160-9200 

Seat Assembly, 1 PC w/ Standard Footrest 

16 

800-0313 

Washer, Flat #3/8 

17 

800-2027  

Screw, Hex Hd - #3/8-16 x 3.25 L 

18 

800-3000A 

aXs2 Motor Enclosure Assembly 

19 

800-0330 

Screw, Self-Threading #4-20 x ½ L 

20 

900-1000  

aXs Seat Belt Assembly (Black) (not shown) 

21 

800-0318 

Bushing, Oilite 

22 

800-2000 

3/8-16 Nyloc Nut 

23 

800-0147  

Screw, 3/8-16 x 2.5” L 

24 

300-6200L  

Locking Deck Anchor (not shown) 

25 

AX3700-1 

Spindle Housing Assembly 

26 

170-3000A 

Arm Rest Assembly (Pair) 

27 

160-2300A 

Footrest Kit (Gray) 

28 

800-0304 

Screw, Hex Hd - #5/16-18 x 4.0” L 

29 

800-0310 

Washer, Flat - #5/16” 

30 

800-0202 

Acorn Nut, #5/16” 

Summary of Contents for aXs2

























Reviews: