background image

16

17

Mixing the Fuel

DANGER:

Gasoline is extremely flammable and explosive. 

A fire or explosion from gasoline will burn you 

and others.

This product is powered by a 2-cycle engine and requires pre-

mixing gasoline and 2-cycle oil. The oil mix should be 50:1, 

using oil that meets or exceeds JASO-FC specifications.
Follow these steps to mix the fuel.

1.

  Obtain a clean container that is approved for use with 

gasoline.

2.

  Mix the 2-cycle engine oil provided with unleaded 

gasoline in the container, according to the instructions 

on the oil carton.

Important: 

This engine is certified to operate on unleaded 

gasoline intended for automotive use with an octane rating 

of 87 ([R + M] / 2) or higher. Do not use automotive oil or 

2-cycle outboard oil. Store the container out of the reach of 

children.

Operation

Filling the Tank

WARNING:

Always stop the engine before filling the tank. 

Never add fuel to a machine with a running or 

hot engine. Move at least 30 ft. (9 m) away from 

the refueling site before starting the engine. Do 

not smoke while filling the tank.

Follow these steps to fill the tank.

1.

  Clean the surface around the fuel cap to prevent con-

tamination.

2.

  Loosen the fuel cap by turning it counterclockwise.

3.

  Pour the fuel mixture carefully into the tank.

4.

  Clean and inspect the gasket. 

 

Note: 

Replace the fuel cap if the gasket is damaged.

5.

  Install the fuel cap and tighten it by turning it clock-

wise.

WARNING:

Check for fuel leaks. If you find any leaks, correct 

the problem before using the product.

6.

  Wipe spilled fuel from the product.

7.

  Move at least 30 ft. (9 m) away before starting the 

product.

 

Note: 

It is normal for the engine to emit smoke during 

use.

Operation

WARNING:

Do not allow familiarity with tools to make you 

careless. Remember that a careless fraction of a 

second is sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses 

with side shields when operating power tools. 

Failure to do so could result in objects being 

thrown into your eyes resulting in possible seri-

ous injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool. 

The use of attachments or accessories not rec-

ommended can result in serious personal injury.

Applications

Use this product for the following applications:

■ 

Cutting grass, weeds, and light undergrowth 

 

(all models)

■ 

Edging along sidewalks and driveways (all models)

■ 

Cutting pulpy weeds, vines, and light brush 

 

(Model No. ZR51990A)

50:1 Gasoline to Oil Mixing Chart

Gasoline 

Oil

1/2 US gallon 

1.3 oz.

1 US gallon 

2.6 oz.

2 US gallons 

5.2 oz.

1 liter 

20 ml

2 liters 

40 ml

3 liters 

60 ml

4 liters 

80 ml

5 liters 

100 ml

 

+     = 

Summary of Contents for ZR51950A





























Reviews: