Ryobi XBD-1850, Owner'S Operating Manual

Page: 5 / 8

4
This tool is started and stopped by depressing and releasing
the trigger (6).
The drill speed is variable from 0 through 400min
-1
(Low
speed position) or from 0 through 1,200min
-1
(High speed
position) by controlling the trigger-squeezing force.
This tool is equipped with a LED work light (5) to illuminate the
tip of a bit. The light turns on by depressing the trigger.
To change the direction of rotation, stop the tool by releasing
the trigger and push the forward/reverse switch (4) to the
opposite side. When the reversing switch is set to the “R”
mark, the direction of rotation will be clockwise when viewed
from the handle end of the drill. When the reversing switch
is set to the “L” mark, the direction of rotation will be
counter-clockwise.
The trigger can be locked by positioning the reversing
switch at the center. Lock the trigger whenever the tool is
not in use.
1. Keyless chuck
2. Torque adjustment cap
3. Speed selector
4. Forward/Reverse switch
5. LED work light
6. Trigger
7. Battery clip
8. Battery pack (Not included)
9. Bit storage
1. Make sure that the tool is only connected to the voltage
marked on the name plate.
2. Never use the tool if its cover or any bolts are missing. If
the cover or bolts have been removed, replace them
prior to use.
Maintain all parts in good working order.
3. Always secure the tool when working in elevated
positions.
4. Never touch the blade, drill bit, grinding wheel or other
moving parts during use.
5. Never start the tool when its rotating component is in
contact with the work piece.
6. Never lay the tool down before its moving parts have
come to a complete stop.
7.
ACCESSORIES: The use of accessories or attachments
other than those recommended in this manual might
present a hazard.
8.
REPLACEMENT PARTS: When servicing use only
identical replacement parts.
1. Be aware that since this tool does not have to be plugged
into an electrical outlet, it is always in operating condition.
2. First, charge the battery.
3. Be sure the battery holder is securely snapped in place.
4. When not in use, lock the trigger.
5. When operating at high places, be aware of things below
you.
6. Before drilling into walls, ceilings or floors, ensure that
there are no concealed power cables inside.
INSTRUCTIONS FOR SAFE HANDLING
CORDLESS DRIVER DRILL SAFETY
PRECAUTIONS
Li-ion batteries must be recycled.
Take the battery to the shop from which it was purchased as
soon as the post-charging battery life becomes too short for
practical use.
Do not discard the exhausted battery.
DISPOSAL OF THE EXHAUSTED BATTERY
DESCRIPTION
Voltage ....................................................................... 18V
No load speed ..................................... 0-400/0-1,500min
-1
Chuck .......................................................................13mm
Clutch ........................................................................ 21+1
Max torque ............................................................... 45Nm
Drilling capacities
in steel ......................................................
8mm
in wood ................................................... 25 mm
Net weight (not incl. battery pack) ....…….…..........…1.1kg
SPECIFICATIONS
STANDARD ACCESSORIES
COMPATIBLE BATTERY PACK AND CHARGER
KEYLESS CHUCK AND MOUNTING THE BIT
(Fig.1, 2)
TRIGGER (Fig. 3)
FORWARD/REVERSE SWITCH (Fig. 3)
LED WORK LIGHT (Fig. 3)
Driver bit x 1pce
This tool comes equipped with a keyless chuck (1) to easily
mount the bit.
Insert the bit into the chuck as far as it will go and rotate the
chuck clockwise to securely tighten the bit.
The bit can be removed by turning the chuck counterclockwise.
WARNING!
Make sure to insert the drill bit straight into the
chuck jaws. Do not insert the drill bit into the chuck jaws at
an angle then tighten, as shown in figure 2. This could cause
the drill bit to be thrown from the drill, resulting in possible
serious personal injury or damage to the chuck.
BATTERY PACK (not included) ...... XB-1500, XB-3000
CHARGER (not included) ............... XPP-2700