background image

  Introduction ..................................................................................................................................................................... 

  Warranty .......................................................................................................................................................................... 

  General Safety Rules ....................................................................................................................................................3-4

  Specific Safety Rules ....................................................................................................................................................4-5

 

Symbols ........................................................................................................................................................................6-7

  Electrical .......................................................................................................................................................................... 8

  Glossary of Terms ............................................................................................................................................................ 9

  Features ....................................................................................................................................................................10-1

  Tools Needed ................................................................................................................................................................. 1

  Loose Parts ................................................................................................................................................................... 13

  Assembly ..................................................................................................................................................................14-0

  Operation ..................................................................................................................................................................1-7

  Adjustments ................................................................................................................................................................... 8

  Maintenance .............................................................................................................................................................9-30

  Parts Ordering / Service ................................................................................................................................... Back page

TABLE OF CONTENTS

INTRODUCTION

This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have 
been given top priority in the design of this product making it easy to maintain and operate.

WARRANTy

RyOBI

®

 POWER TOOL - LIMITED TWO yEAR WARRANTy AND 30 DAy EXCHANGE POLICy

One World Technologies, Inc., warrants its RYOBI

® 

power tools with the following conditions:

30-DAy EXCHANGE POLICy: During the first 30 days after date of purchase, you may either request service under this 
warranty or you may exchange any RYOBI

®

 power tool which does not work properly due to defective workmanship or 

materials by returning the power tool to the dealer from which it was purchased. To receive a replacement power tool 
or requested warranty service, you must present proof of purchase and return all original equipment packaged with the 
original product. The replacement power tool will be covered by the limited warranty for the balance of the two year period 
from the date of the original purchase.
WHAT THIS WARRANTy COVERS: This warranty covers all defects in workmanship or materials in your RYOBI

®

 power 

tool  for  a  period  of  two  years  from  the  date  of  purchase.  With  the  exception  of  batteries,  power  tool  accessories  are 
warranted for ninety (90) days. Batteries are warranted for two years.
HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, to an Authorized Service 
Center.  You  can  obtain  the  location  of  the  Service  Center  nearest  you  by  contacting  a  service  representative  at  One 
World Technologies, Inc., P.O. Box 107, Anderson, SC 96-107, by calling 1-800-55-579 or by logging on to www.
ryobitools.com.  When  you  request  warranty  service,  you  must  also  present  proof  of  purchase  documentation,  which 
includes the date of purchase (for example, a bill of sale). We will repair any faulty workmanship, and either repair or replace 
any defective part, at our option. We will do so without any charge to you. We will complete the work in a reasonable time, 
but, in any case, within ninety (90) days or less.
WHAT’S NOT COVERED: This warranty applies only to the original purchaser at retail and may not be transferred. This 
warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defects resulting 
from  misuse,  abuse,  neglect,  alteration,  modification  or  repairs  by  other  than  Authorized  Service  Centers.  One  World 
Technologies, Inc. makes no warranties, representations or promises as to the quality or performance of its power tools 
other than those specifically stated in this warranty.
ADDITIONAL LIMITATIONS: Any implied warranties granted under state law, including warranties of merchantability or 
fitness for a particular purpose, are limited to two years from the date of purchase. One World Technologies, Inc. is not 
responsible for direct, indirect, or incidental damages, so the above limitations and exclusions may not apply to you. This 
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Summary of Contents for TS1342LBF

































Reviews: