![background image](http://html1.mh-extra.com/html/ryobi/sp-1218/sp-1218_owners-operating-manual_1506340005.webp)
4
MAINTENANCE
To reduce the risk of injury, user must read
instruction manual.
To ensure safety and reliability, all repairs should be
performed by an AUTHORIZED SERVICE CENTER or
other QUALIFIED SERVICE ORGANIZATION.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
WARNING!
WARNING!
INSERTING THE BASE OF THE DISC(Fig.2)
WOOL BONNET
SPEED SELECTOR
ON/OFF SWITCH TRIGGER
LOCK-ON BUTTON
CLEANING
WARNING!
After use, check the tool to make sure that it is in top
condition. It is recommended that you take this tool to a
RYOBI Authorized Service Center for a thorough cleaning
and lubrication at least once a year.
DO NOT MAKE ANY ADJUSTMENTS WHILE THE
MOTOR IS IN MOTION.
ALWAYS DISCONNECT THE POWER CORD FROM THE
RECEPTACLE BEFORE CHANGING REMOVABLE OR
EXPENDABLE PARTS (BLADE, BIT, SANDING PAPER
ETC.), LUBRICATING OR WORKING ON THE UNIT.
• Press the spindle lock button (2) and secure the press
disc base (1) by turning it clockwise, with the spindle
facing up.
• Adjust the base by hand do not use additional tools to do
so.
• Make Sure the base is fìxed to the spindle and that it
can run freelγ, without binding.
• Since everyone does not use the same type of polisher ,
we recommend you clean and polish a test section on a
flat area first. From this test section you can judge
the strength or cleaning action of your polish.
• Washing will remove loose dirt, scum, road salt, Which
could act as an abrasive and damage paint. Loose dirt,
etc. Will also clog the woolen pad and you will have to
clean it more often.
TIPS
• Apply about two tablespoons of wax (not included)
evenly on the clean foam pad.
• When polishing we recommend doing it in a crisscross
pattern over the surface.
• Do not exert pressure on the polisher, as the tool does
the job by itself. You can only press lightly when working
in corners or angles.
• You should use most care when power polishing
around or over sharp objects and contours. It is very
important to apply the correct pressure.
• Always apply the pad/bonnet flat against the surface.
• Keep the ventilation slots of the machine clean to
prevent overheating of the Engine.
• Regularly clean the machine housing with a soft cloth,
preferably after each use.
• Keep the ventilation slots free from dust and dirt.
• lf the dirt does not come off use a soft cloth moistened
with soapy water.Never use solvents such as petrol,
alcohol , ammonia water, etc.These solvents may
damage the plastic parts.
• Place the wool bonnet on the base of the disc and
stretch it until it hooks over the edges.
• Pull the string of the wool bonnet to adjust it and make a
knot.
• After knotting the wool bonnet, insert the remaining string
within it to prevent loosening during operation.
• To remove
the wool bonnet , untie and remove it carefully
from the edges.
• To switch the tool on,
press the on/off switch trigger (7).
• To switch the
tool off, release the on/off switch trigger (7).
• This tool has a lock-on button (5), for continuous operation,
press the lock-on button while on/off switch trigger (7) is
depressed. Depress again to release the lock.
Never press the spindle lock button wíth the
tool running or coasting.
ATTENTION!
The disc continues to rotate for a short time
after the tool is switched off.
CAUTION:
Use only lower speeds for polishing. If not,
damage may occur to the paint being polished.
Set the desired speed before turning the tool on, using the
speed selector (4)
Summary of Contents for SP-1218
Page 1: ...SP 1218...
Page 2: ...1 1 2 2 7 1 10 4 3 6 9 8 5 1 2 3 Hole A...
Page 6: ...5 NOTE...
Page 7: ...6 NOTE...