background image

Page 5

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

WARNING:

Read and understand all instructions. Failure to
follow all instructions listed below, may result in elec-
tric shock, fire and/or serious personal injury.

Never use a battery that has been dropped or
received a sharp blow. 
A damaged battery is subject
to explosion. Properly dispose of a dropped battery
immediately. Failure to heed this warning can result in
serious personal injury.

Save these instructions. This manual contains impor-
tant safety and operating instructions for charger.

Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. 
Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.

CAUTION: To reduce risk of injury, charge only nickel-
cadmium type rechargeable batteries. Other types of
batteries may burst causing personal injury and dam-
age.
 Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.

Do not expose charger to wet or damp conditions.
Following this rule will reduce the risk of electric shock, fire,
or serious personal injury.

Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons. 
Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.

To reduce risk of damage to charger body and cord,
pull by charger plug rather than cord when discon-
necting charger. 
 Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.

Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress. 
Following this rule will reduce the risk of serious
personal injury.

Do not abuse cord. Never carry tool by cord or yank
it to disconnect from receptacle. Keep cord from
heat, oil and sharp edges. 
Following this rule will reduce
the risk of electric shock or fire.

An extension cord should not be used unless abso-
lutely necessary. 
 Use of improper extension cord could
result in a risk of fire and electric shock. If extension cord
must be used, make sure:

a.  That pins on plug of extension cord are the
     same number, size and shape as those of
     plug on charger.

b.  That extension cord is properly wired and in
     good electrical condition; and

c.  That wire size is large enough for AC ampere
     rating of charger as specified below:

     Cord Length (Feet)

25'

50'

100'

     Cord Size (AWG)

16

16

16

     Note: AWG = American Wire Gage

Do not operate charger with a damaged cord or plug.
If damaged, have replaced immediately by a qualified
serviceman.  
Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.

Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way;
take it to a qualified serviceman. 
Following this rule will
reduce the risk of electric shock, fire, or serious personal
injury.

Do not disassemble charger; take it to a qualified
serviceman when service or repair is required. Incor-
rect reassembly may result in a risk of electric shock
or fire. 
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.

To reduce the risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk.  
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.

Disconnect charger from power supply when not in
use.  
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.

Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instruc-
tions also. 
Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.

WARNING:

Some dust created by power sanding, sawing, grind-
ing, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and
other masonry products, and

arsenic and chromium from chemically-treated
lumber.

Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well venti-
lated area, and work with approved safety equipment,
such as those dust masks that are specially designed
to filter out microscopic particles.

SAVE THESE INSTRUCTIONS

Summary of Contents for SA1202





















Reviews: