background image

16

        WARNING:

Current  attachments  and  accessories  available 
for  use  with  this  tool  are  listed.  Do  not  use  any 
attachments  or  accessories  not  recommended  by  the 
manufacturer  of  this  tool.  The  use  of  attachments  or 
accessories  not  recommended  can  result  in  serious 
personal injury.

ACCESSORIES

The following recommended accessories are currently 
available.

ACCESSORIES

Air Filter .........................................Power Care - AP04107
Spark Plug......................................... Champion - RCJ-6Y
Fuel Cap .............................................................. AP04108
2-Cycle Oil.......................... (2.6 FL. OZ - 76 ml) AR99G01

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORIZED SERVICING DEALER.

PROBLEM

CAUSE

REMEDY

Engine fails to start.

No fuel in tank.
Spark plug shorted or fouled.
Spark plug is broken (cracked 
porcelain or electrodes broken).
Ignition lead wire shorted, broken, or 
disconnected from spark plug.
Ignition inoperative.

Fill tank.
Replace spark plug.
Replace spark plug.

Replace lead wire or attach to spark 
plug.
Contact authorized service center.

Engine hard to start.

Water in gasoline or stale fuel mixture.

Too much oil in fuel mixture.
Engine is under or over choked.
Weak spark at spark plug.

Drain entire system and refill with fresh 
fuel.
Drain and refill with correct mixture.
Adjust choke as necessary.
Contact authorized service center.

Engine lacks power.

Air filter clogged.

Clean or replace air filter.

Engine overheats.

Insufficient oil in fuel mixture.

Mix fuel as described in starting 
instructions.

Summary of Contents for RY08510





















Reviews: