background image

11

PREMIUM EXACT MIX™ (50:1)

              GASOLINE                                OIL

              1 gallon (US)                             2.6 oz.
                  1 Liter                              20 cc (20 ml)

FILLING THE TANK

        WARNING:

Always stop the engine before filling the fuel tank. Never 
add fuel to a machine with a running or hot engine. Move 
at least 30 ft. from the refueling area before starting engine. 
Do not smoke while filling the tank.

n

  Clean the surface around the fuel cap to prevent contami-

nation.

n

  Loosen  the  fuel  cap  slowly,  by  turning  it  counter-

clockwise.

n

  Pour the fuel mixture carefully into the tank.

n

  Clean and inspect the fuel cap gasket before replacing 

the fuel cap.

n

  Replace the fuel cap and tighten it by turning it clock-

wise.

n

  Wipe spilled fuel from the product.

n

  Move at least 30 ft. away from refueling area before start-

ing the product.

NOTE: 

It  is  normal  for  smoke  to  be  emitted  from  a  new 

engine during first use.

        WARNING:

Check for fuel leaks. If you find any leaks, correct the 
problem before using the product.

        WARNING:

A leaking fuel cap is a fire hazard and must be replaced 
immediately.

WARNING:

Do  not  allow  familiarity  with  tools  to  make  you  care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side 
shields  when  operating  power  tools.  Failure  to  do  so 
could  result  in  objects  being  thrown  into  your  eyes
resulting in possible serious injury.

APPLICATIONS

You may use this tool for the purposes listed below:

Clear leaves and other debris from your lawn

Keep  decks  and  driveways  free  from  leaves  and  pine 
needles

        WARNING:

Gasoline is extremely flammable and explosive. A fire or 
explosion from gasoline will burn you and others.

MIXING THE FUEL

This product is powered by a 2-cycle engine and requires 
pre-mixing gasoline and 2-cycle oil.  The mixture should be 
at a 50:1 ratio, using Premium Exact Mix™ 2-cycle engine 
oil. If Premium Exact Mix™ 2-cycle engine oil is not avail-
able, use a high quality 2-cycle engine oil, mixed at a 50:1 
ratio. See chart later in this section.

To mix the fuel:

n

  Use a clean container that is approved for use with gaso-

line.

n

  Mix  the  Premium  Exact  Mix™  2-cycle  engine  oil  with 

unleaded  gasoline  in  the  container,  according  to  the 
instructions on the oil package.

NOTE: 

This engine is certified to operate on unleaded gaso-

line intended for automotive use with an octane rating of 87 
[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle 
outboard oil.

NOTE: 

Premium Exact Mix™ fuel mixture will stay fresh up 

to 30 days. DO NOT mix quantities larger than can be used 
in a 30 day period.

OPERATION

Summary of Contents for RY08510





















Reviews: