EC DECLARATION OF CONFORMITY
Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
We declare as the manufacturer under our sole responsibility that the product
mentioned below
Rotary tool
Brand: RYOBI
Model number: RRT18
Serial number range: 47546501000001 - 47546501999999
fulfills all the relevant provisions of the following European Directives, European
Regulations and harmonised standards.
2006/42/EC, 2014/30/EU, 2011/65/EU
EN 55014-1:2017+A11:2020, EN 55014-2:2015,
EN 60745-1:2009+A11:2010, EN 60745-2-23:2013,
EN IEC 63000:2018
Todd Chipner
Vice President, Quality - Ryobi Asia
Winnenden,
Mar. 10, 2021
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
RYOBI
®
WARRANTY APPLICATION CONDITIONS
In addition to any statutory rights resulting from the purchase, this product is
covered by a warranty as stated below.
1. The warranty period is 24 months for consumers and commences on the
date the product was purchased. This date has to be documented by an
invoice or other proof of purchase. The product is designed and dedicated to
consumer and private use only. So there is no warranty provided in case of
professional or commercial use. This warranty applies only on new products.
2. There is a possibility to extend for a part of the range of power tools
(AC/DC) the warranty period over the period described above using the
registration on the www.ryobitools.eu website. The eligibility of products for
extended warranty is clearly displayed in stores and / or on packaging and
is contained within the product documentation. The end user is required to
register his/her newly-acquired products online within 30 days from the date
of purchase. The end user may register for the extended warranty in his/her
country of residence if listed on the online registration form where this option
is valid. Furthermore, end users must give their consent to the storage of
their personal data that is required to be entered online. They must also
accept the terms and conditions. The registration confirmation receipt, which
is sent out by e-mail, and the original invoice showing the date of purchase
will serve as proof of the extended warranty.
3. The warranty covers all defects of the product during the warranty period
due to faults in workmanship or material at the purchase date. The warranty
is limited to repair and/or replacement and does not include any other
obligations including but not limited to incidental or consequential damages.
The warranty is not valid if the product has been misused, used contrary to
the instruction manual, or has been incorrectly connected to a power supply.
This warranty does not apply to:
–
any damage to the product that is the result of improper or lack of
maintenance
–
any product that has been altered or modified
–
any product where original identification (trade mark, serial number)
markings have been defaced, altered or removed
–
any damage caused by non-observance of the instruction manual
–
any product not displaying the CE approval mark on the rating plate
–
any product that has been attempted to be repaired by a non-
authorised warranty service centre or without prior authorisation by
Techtronic Industries
–
any product connected to improper power supply (amps, voltage,
frequency)
–
any damage caused by external influences (water, chemical, physical,
shocks) or foreign substances
–
normal wear and tear spare parts
–
inappropriate use, overloading of the tool
–
use of non-approved accessories or parts
–
Power tool accessories provided with the tool or purchased separately,
including but not limited to screw driver bits, drill bits, abrasive discs,
sand paper and blades, lateral guide, etc.
–
Components (parts and accessories) subject to natural wear and tear,
including but not limited to service & maintenance kits, carbon brushes,
bearings, chuck, SDS drill bit attachment or reception, power cord,
auxiliary handle, transport carry case, sanding plate, dust bag, dust
exhaust tube, felt washers, impact wrench pins & springs, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorised
service station listed for each country in the following list of service station
addresses. In some countries your local RYOBI dealer undertakes to send
the product to the RYOBI service organisation. When sending a product
to a RYOBI service station, the product should be safely packed without
any dangerous contents such as petrol, marked with sender’s address and
accompanied by a short description of the fault.
5. A repair / replacement under this warranty is free of charge. It does not
constitute an extension or a new start of the warranty period. Exchanged
parts or products become our property. In some countries delivery charges
or postage will have to be paid by the sender. Your statutory rights arising
from the purchase of the product remain unaffected
6. This warranty is valid in the European Community, Switzerland, Iceland,
Norway, Liechtenstein, Turkey, Russia and the United Kingdom. Outside
these areas, please contact your authorised RYOBI dealer to determine if
another warranty applies.
AUTHORISED SERVICE CENTRES
Any request or issue with the product can be addressed to your local authorised
service centres (visit www.ryobitools.eu) or directly to: Techtronic Industries
GmbH, Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial
number and product type printed on the label.
RYOBI is a trade mark of Ryobi Limited,
and is used under license.
© 2021 Techtronic Cordless GP.
GB-DECLARATION OF CONFORMITY
Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
We declare as the manufacturer under our sole responsibility that the product
mentioned below
Rotary tool
Brand: RYOBI
Model number: RRT18
Serial number range: 47546501000001 - 47546501999999
fulfills all the relevant provisions of the following Regulations: S.I. 2008/1597 (as
amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 55014-1:2017+A11:2020, BS EN 55014-2:2015,
BS EN 60745-1:2009+A11:2010, BS EN 60745-2-23:2013,
BS EN IEC 63000:2018
Todd Chipner
Vice President, Quality - Ryobi Asia
Winnenden,
Mar. 10, 2021
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
