Ryobi RPW140SC, Original Instructions Manual

Page: 4 / 24

2
WARNING
High pressure cleaners are dangerous if misused. The
jet must not be directed at persons, animals, electrical
devices, or the product itself.
■ Hold the handle securely with both hands. Expect the
trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
■ Exercise caution to avoid slipping or falling.
■ Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance.
■ Use only recommended accessories. The use of
improper accessories may cause risk of injury.
■ Never leave the product running unattended. Turn the
power off. Do not leave the product until it comes to a
complete stop.
■ Be familiar with the controls. Know how to stop the
product and bleed the pressure quickly.
■ Stay alert and exercise control. Watch what you are
doing and use common sense.
■ Do not use a product when you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating the product may result in
serious personal injury.
■ Do not use the product if the switch does not turn it
on and off. Any product that cannot be controlled with
switch is dangerous and must be repaired.
■ Keep a minimum distance of 30 cm when cleaning
vehicles. The high high-pressure jet may damage or
burst vehicle tires and/or tire valves.
OVERLOAD PROTECTION
The product has an overload protection device that is
activated when overheating or a current spike occurs,
automatically shutting down power within the product. To
resume operation, disconnect the product from the power
supply, wait for about 15 minutes, and re-connect the
product to the power supply.
TRANSPORTATION AND STORAGE
■ Stop the product, disconnect from the power supply,
and allow the product to cool. Disconnect the product
from the water supply before storing or transporting.
Never place the product in any position other than
upright.
■ Consider the weight of the product when choosing a
storage location.
■ Clean all foreign material from the product. Store it in a
cool, dry, and well-ventilated place that is inaccessible
to children. Keep away from corrosive agents such
as garden chemicals and de-icing salts. Do not store
outdoors.
■ For transportation in a vehicle, secure the product
against movement or falling to prevent injury to persons
or damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories and attachments. Failure to do so can
cause possible injury and poor performance, and may
void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service, bring the product to an
authorised service centre. When servicing, use only
identical replacement parts.
■ Stop the product, disconnect from the power supply,
and allow the product to cool. Disconnect the product
from the water supply before:
● cleaning the product
● maintaining the product
● replacing apare parts
■ You may make adjustments .and repairs described in
the manual. For other repairs, contact the authorized
service agent.
■ Check all nuts, .bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■ Injury caused by the high pressure jet. Avoid pointing
the high pressure jet to people, animals, and to yourself.
■ Injury cause by kickback. Always hold the trigger gun or
the trigger wand firmly with your two hands.
■ Injury caused by exposure to noise. Wear ear protection .
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices are
all thought to contribute to the development of the these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■ Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
■ After each period of operation, exercise to increase
blood circulation.
■ Take frequent work breaks. Limit the amount of