3
may increase the risk of injury to yourself
or others.
■
Use only the manufacturer’s replacement
cutting line. Do not use any other cutting
attachment.
■
Immediately switch off and disconnect from
the mains once in the event of accident
or breakdown. Don’t operate the product
again until it’s fully checked by authorised
service center.
TRANSPORTATION AND STORAGE
■
Stop the product and allow it to cool before
storing or transporting.
■
Clean all foreign material from the product.
Store it in a cool dry and well-ventilated
place that is inaccessible to children.
Keep away from corrosive agents such as
garden chemicals and de-icing salts. Do
not store outdoors.
■
For storage, always disconnect from power
supply and wind cable.
■
For transportation, secure the product
against movement or falling to prevent
injury to persons or damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer’s
replacement parts, accessories and
attachments. Failure to do so can cause
possible injury, poor performance, and may
void your warranty.
WARNING
Servicing requires extreme care and
knowledge and should be performed
only be a qualified service technician. For
service we suggest you return the product
to your nearest authorized service center for
repair. When servicing, use only identical
replacement parts.
■
Switch off and disconnect from the mains
before conducting any maintenance or
cleaning work.
■
You may make adjustments and repairs
described here. For other repairs, contact
the authorized service agent.
■
For replacement line, use only nylon
filament line of the diameter described in
the specification table of this manual.
■
After extending new cutter line, always
return the product to its normal operating
position before starting.
■
After each use, clean the product with a
soft dry cloth. Any part that is damaged
should be properly repaired or replaced by
an authorised service centre.
■
Check all nuts, bolts, and screws at
frequent intervals for proper tightness to
ensure the product is in a safe working
condition.
RESIDUAL RISKS
Even when the product is used as prescribed,
it is still impossible to completely eliminate
certain residual risk factors. The following
hazards may arise in use and the operator
should pay special attention to avoid the
following:
■
Injury caused by vibration. Hold the product
by designated handles and restrict working
time and exposure.
■
Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
■
Eye injury due to flying debris. Wear eye
protection at all times.
RISK REDUCTION
It has been reported that vibrations from
hand-held products may contribute to a
condition called Raynaud’s Syndrome in
certain individuals. Symptoms may include
tingling, numbness and blanching of the
fingers, usually apparent upon exposure to
cold. Hereditary factors, exposure to cold and
dampness, diet, smoking and work practices
are all thought to contribute to the development
of the these symptoms. There are measures
that can be taken by the operator to possibly
reduce the effects of vibration:
■
Keep your body warm in cold weather.
When operating the product wear gloves
to keep the hands and wrists warm. It is
reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
■
After each period of operation, exercise to
increase blood circulation.
■
Take frequent work breaks. Limit the
amount of exposure per day.
If you experience any of the symptoms of this
condition, immediately discontinue use and
Summary of Contents for RLT1238
