background image

13

MAintenAnce

Be sure the tool is unplugged.

  1. Your grass trimmer requires no additional lubrication or maintenance. There are no user serviceable parts 

in your power tool.

  2. Your  trimmer  line  can  dry  out  over  time.  To  keep  your  line  in  top  condition,  store spare pre-wound 

spools or bulk line in plastic, sealable bag with a tablespoon of water.

  3. Never use water or chemical cleaners to clean your grass trimmer. Wipe clean with a dry cloth.

  4. Plastic parts may be cleaned by using a mild soap and damp rag.

  5. Always store your grass trimmer in a dry place. No not allow any liquid to get inside it.

  6. Keep the motor ventilation slots clean.

  7. If you see some sparks flashing in the ventilation slots, this is normal and will not damage your power tool.

  8. There are no user serviceable parts in the trimmer. If a fault is suspected return the trimmer to an 

authorized dealer for repair.

IMPORTANT : To assure product safety and reliability, repairs, maintenance and adjustment should be 

performed  by RYOBI authorized service centers or other qualified service organization, 

always using identical replacement parts.

troUBLesHootinG

  1. If trimmer will not operate, check power at mains plug

  2. If  the  trimmer  is  not  cutting  properly  check  the  nylon  line  length  and  lengthen or replace line.

  3. If you experience regular line breakage rewind the spool uniformly.

Summary of Contents for RLT-710

















Reviews: