background image

operAtion

triMMinG

1. Use the trimmer at an angle of approximately 15-degree to the working area (Fig.8).

2. Slowly swing the trimmer from side to side(Fig.9). 

3. Do not overload your trimmer, take small “bites” this will keep machine operating at high speed and will greatly 

improve cutting efficiency, (Fig.10).

4. Cutting close to a wall

  Use the edge guide when cutting close to an edge.

Fig. 8

Fig. 10

Fig. 9

MAnUALLY Feed Line (Fig.11)

If required line can be fed out manually, press and release manual line feed button (11), whilst gently pull out the 

lines until the lines reach the line cutter.

When the required amount of line is fed out, gently pull on the second line (there is no need to press the manual 

line feed button again)

If the line extends past the line cutter, too much line has been fed out.

If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired 

length.

cAUtion: Always wear eye protection.

stArtinG And stoppinG (Fig. 7)

1. Squeeze the trigger switch (2) to start the trimmer.

2. Release the trigger switch to stop the trimmer.

Fig. 7

2

Fig. 11

11

9

Summary of Contents for RLT-350

















Reviews: