Ryobi RLS2200T5, Original Instructions Manual

Page: 3 / 24

1
Safety, performance, and dependability have been given
top priority in the design of your electric log splitter.
INTENDED USE
The log splitter i s designed to split wooden material along
the grain. The logs or similar work pieces must be 200 mm
to 520 mm in length and 100 mm to 250 mm in diameter.
The log splitter is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual and can be considered responsible for their
actions.
The log splitter is intended to be used only in dry, well-
illuminated, and uncluttered work areas and it must be
adequately controlled by using two-handed operation.
The log splitter is not designed to split across the grain or
for processing any other material except wood.
GENERAL SAFETY WARNINGS
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders,
please read these instructions before operating the
product. Please keep the instructions safe for later use.
TRAINING
■ Read the instructions carefully. Be familiar with the
controls and the correct use of the product.
■ Never allow children, persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge, or people unfamiliar with these instructions
to use the product. Local regulations may restrict the
age of the operator.
■ Keep in mind, that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
■ Keep bystanders, children and pets 15 m away from
the area of operation. Stop the product if anyone enters
the area.
■ Never use the product when you are tired, ill or under
the influence of alcohol, drugs or medicine.
PREPARATION
■ Dress properly. Do not wear loose clothing, neckties,
or jewellery that can get caught and draw you into
moving parts. Rubber gloves and nonskid footwear are
recommended when working outdoors. Secure long hair
so it is above shoulder level to prevent entanglement in
moving parts.
■ To help reduce the risk of injury from falling work pieces,
the operator should wear footwear with hardened toe
protection.
■ Wear full eye protection at all times while operating this
product. The manufacturer strongly suggests a full face
mask or fully enclosed goggles. Normal spectacles or
sun glasses are not adequate protection.
■ Ensure before each use that all controls and safety
devices function correctly. Do not use the product if the
“off” switch does not stop the motor.
■ Keep work area clean. Cluttered areas invite accidents.
Do not leave tools or pieces of wood on the product
while it is in operation. Keep the operator zone and
adjacent area clear for safe, secure footing.
■ Make sure the work area has ample lighting to see the
work and that no obstructions will interfere with safe
operation before using the product.
■ Make sure the product is on a level surface.
■ Before use, check that there are no damaged parts. A
defective switch or any part that is damaged should be
properly repaired or replaced by an authorized service
facility.
■ Check damaged parts. Before further use of the
product, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that
is damaged must be properly repaired or replaced by
an authorized service center to avoid risk of personal
injury.
■ Before each use inspect all hydraulic pipes and hoses,
any oil leakage should be proper repaired; check oil
level to ensure it is in normal capacity.
ELECTRICAL SAFETY
■ Power plugs must match the outlet. Never modify the
plug in any way. Unmodified plugs and matching outlets
will reduce risk of electric shock.
■ Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
■ Do not expose this product to rain or wet conditions.
Water entering an appliance will increase the risk of
electric shock.
■ Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA.
■ Before every use, examine the power cord for damage.
If there are signs of damage, it must be replaced by at
an authorised service centre. Always uncoil the power
cord during use; coiled cables can overheat.
■ If the cord becomes damaged during use, disconnect
the cord from the power supply immediately. Do not
touch the cord before disconnecting the power
supply . Do not use the product if the cord is damaged
or worn.
■ If you need to use an extension cord, ensure it is
suitable for outdoor use and has a current capacity
rating sufficient to supply your tool. Check the extension
cord before every use for damage. Always uncoil the
extension cord during use because coiled cords can
overheat. Damaged extension cords should not be
repaired, they should be replaced with an equivalent
type.
■ Make sure the power cord is positioned so that it will not