6
Vacuum bag adaptor
2-Stroke engine lubricant
Operator’s manual
Figure sheet
NOTE:
Read and remove all hang tags and store with your
operator’s manual.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Using the product with
damaged or missing parts could result in serious personal
injury.
WARNING:
Do not attempt to modify this product or create accessories
not recommended for use with this product. Any such
DOWHUDWLRQRUPRGL¿FDWLRQLVPLVXVHDQGFRXOGUHVXOWLQD
hazardous condition leading to possible serious personal
injury.
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
ASSEMBLING THE BLOWER TUBES
See Figure 2.
Align raised tabs on upper tube to the slots on blower
housing outlet; slide together and tighten securely by
twisting. Check tightness after initial use and retighten if
needed.
Attach desired nozzle (high velocity nozzle or sweeper
nozzle) to upper blower tube by aligning raised tabs on
upper blower tube; slide together and tighten securely by
twisting. Check tightness after initial use and retighten if
needed.
To remove the nozzle, rotate the nozzle to unlock and
remove from the upper blower tube.
INSTALLING THE VACUUM BAG
See Figures 3 - 4.
8VLQJWKHÀDWKHDGVFUHZGULYHURIWKHFRPELQDWLRQZUHQFK
lift locking tab on the upper blower tube and rotate to
unlock position. Then remove the upper blower tube.
Unzip the vacuum bag and place the adaptor inside as
shown. Push the vacuum bag adaptor through the opening
opposite the zipper. The end of the adaptor with the tapered
ÀDQJHZLOOUHPDLQRQWKHLQVLGHRIWKHYDFXXPEDJZKHQ
installed properly.
Align the raised slots on the vacuum bag adaptor with the
raised locking tabs on the blower housing outlet; push the
bag adaptor onto the housing. Twist to lock into place.
Rotate the vacuum bag until the shoulder strap is upright.
Make sure the vacuum bag is zipped and closed before
starting the product.
INSTALLING THE VACUUM TUBES
See Figures 5 - 6.
WARNING:
Rotating impeller blades can cause severe injury. Always
stop the engine and ensure impeller blades have stopped
rotating before opening the vacuum door or installing/
changing tubes. Do not put hands or any other object into
the vacuum tubes while they are installed on the product.
To install the vacuum tubes:
Secure the upper and lower vacuum tubes together by
aligning the raised locking tabs with the raised slots.
Tap tube assembly on ground until the screw holes in lower
tube are in the raised slot of the upper tube. Secure with
supplied screws.
'HSUHVVLQOHWFRYHUWDEXVLQJDÀDWKHDGVFUHZGULYHUDQG
open vacuum inlet cover.
Align tabs on housing with tube assembly.
Tighten screws on upper vacuum tube to secure to blower
housing.
To remove the vacuum tubes:
Loosen screws of the upper vacuum tube by turning
counterclockwise.
Remove the vacuum tube assembly from the blower
housing.
Close the vacuum inlet cover door securely.
To remove the adaptor:
8VLQJDÀDWKHDGVFUHZGULYHUOLIWORFNLQJWDEDQGURWDWH
the adaptor to unlock position. Then remove the adaptor.
OPERATION
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second is
VXI¿FLHQWWRLQÀLFWVHULRXVLQMXU\
WARNING:
Always wear eye protection with side shields marked to
comply with standards, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes and other possible serious injuries.
MIXING THE FUEL
This product is powered by a 2-stroke engine and requires
premixing petrol and 2-stroke oil. The mixture should be at
a 50:1 ratio.
NOTE:
We recommend you use Ryobi synthetic 2-stroke
lubricant. Only use a quality synthetic 2-stroke lubricant in
your blower to ensure top performance and engine longevity.
Summary of Contents for RBV26GN
Page 11: ...11...
