Ryobi RBC52FSBHO, Original Instructions Manual

Page: 10 / 48

8
from the sharp blades and carefully remove the debris.
CUTTING TIPS
Ŷ
Do not push into the grass to be cut. Move from side to
side, moving forward a little at the end of each sweep.
Ŷ
Keep the product tilted towards the area being cut.
Ŷ
Do not use in dangerous environments.
Ŷ
Use the tip of the string to do the cutting; do not force
the string head into the uncut grass.
Ŷ
Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, kerbs, and wood may
wear string rapidly.
Ŷ
Avoid trees and shrubs. Tree bark, wood mouldings,
cladding and fence posts can be easily damaged by
the string.
ADVANCING THE REEL EASY LINE
Line advance is controlled by tapping the string head on
grass while running engine at full throttle.
Ŷ
Run engine at full throttle.
Ŷ
Tap the knob on ground to advance string. The string
advances each time the knob is tapped. Do not hold the
knob on the ground.
Ŷ
The string should advance until it is cut to length by
the line cutting blade located on the cutting attachment
guard.
OPERATING THE BRUSHCUTTER
Ŷ
To help reduce the risk of kickback, do not push into
the material to be cut. Move from right to left in steady
sweeps, moving forward a little at the beginning of each
new sweep.
Ŷ
Hold the product with the right hand on the trigger
handle and the left hand on the left handle. Keep a firm
grip with both hands while in operation.
Ŷ
The product should be held at a comfortable position
with the trigger handle about hip height.
Ŷ
Maintain your grip and balance on both feet. Position
yourself so that you will not be thrown off balance by the
kickback reaction of the cutting blade.
Ŷ
Adjust the strap hanger to a comfortable position.
BLADE
The blade is suitable for cutting pulpy weeds and vines
only. When the blade becomes dull, it can be turned over to
extend its life. Do not sharpen the blade.
CUTTING TECHNIQUE
WARNING
The blades are very sharp and can injure even if they
are not moving. Exercise extreme caution when using
the blade with the product. Safe operation of the
product requires that you read and understand this
RSHUDWRU¶VPDQXDODQGDOOODEHOVDI¿[HGWRWKHSURGXFW
Ŷ
Both hands must be used at all times to control the
product. Keep a firm grip with both hands while in
operation.
Ŷ
Maintain your grip and balance on both feet. Position
yourself so that you will not be drawn off balance by the
kickback reaction of the cutting blade.
Ŷ
Inspect and clear the area of any hidden objects such
as glass, stones, concrete, fencing, wire, wood, and
metal.
Ŷ
Never use blades near footpaths, fencing, posts,
buildings or other immovable objects.
Ŷ
Never use a blade after hitting a hard object without
first inspecting it for damage. Do not use if any damage
is detected.
Ŷ
For cutting ease and safety, approach the weeds being
cut from the right to the left.
REPLACING THE REEL EASY LINE
Ŷ (QVXUHWKHSURGXFWLVLQWKH³6723´2))SRVLWLRQ
Ŷ
Use a 2.4 mm diameter monofilament string.
Ŷ
Cut one piece of string approximately 6 m in length.
Ŷ
Rotate the knob on the string head until the line on knob
aligns with the arrows on the top of string head.
Ŷ
Insert one end of the string into the eyelet located on the
side of the string head and push until the string comes
out through the eyelet on the other side. Continue to
push the string until its middle section is inside the
string head and the string outside the string head is
evenly divided on each side.
Ŷ
Rotate the knob on the string head clockwise to wind
the string.
Ŷ :LQG WKH VWULQJ XQWLO DSSUR[LPDWHO\ FP UHPDLQV
protruding from the string head.
BLADE PROTECTOR
Always place the blade protector on the blade when the
product is not in use. The blade protector has clips round
the edges to snap over the blade and keep it in place. Wear
gloves and be cautious when handling the blade.
NOTE : Always remove the blade protector before using the
product. If not removed, the blade protector could become
a thrown object as the blade begins to turn.
CLEANING THE EXHAUST PORT AND SILENCER
Depending on the type of fuel used, the type and amount of
oil used, and/or your operating conditions, the exhaust port
and silencer may become blocked with carbon deposits.
If you notice a power loss with your petrol-powered tool,
D TXDOL¿HG VHUYLFH WHFKQLFLDQ ZLOO QHHG WR UHPRYH WKHVH
deposits to restore performance.
CLEANING THE AIR FILTER
Ŷ
Make sure the product is in the “off” position.
Ŷ
Remove the air filter knob and air filter cover.
Ŷ
Remove the air filter and clean it with warm soapy
water.
Ŷ
Rinse, and let the air filter dry completely.