background image

2

Original Instructions

IMPORTANT!

It is essential that you read the instructions in this manual 

before assembling, operating, and maintaining the 

product.

Subject to technical modification.

Safety, performance, and dependability have been given top 

priority in the design of your cordless line trimmer or edge 

trimmer.

INTENDED USE

The cordless line trimmer or edge trimmer is intended to 

be used only by adults who have read and understood 

the instructions and warnings in this manual and can be 

considered responsible for their actions.
The product is intended only for outdoor use in a well-

ventilated area. For safety reasons, the product must be 

adequately controlled by a two-handed operation.

When  fitted  with  the  line  trimmer  head  (and  appropriate 

guard), the product is intended for cutting long grass, pulpy 

weed, and similar vegetation at or about ground level. The 

cutting plane should be approximately parallel to the ground 

surface.
The cutting plane should be approximately parallel to the 

ground surface when trimming and approximately vertical 

when edging.
The product should not be used to cut or trim hedges, 

bushes, or other vegetation where the cutting plane is not 

parallel to the ground surface.
Do not use the product for any other purpose.

GENERAL SAFETY WARNINGS

 WARNING! Read all safety warnings and all 

instructions. 

Failure to follow the warnings and instructions 

may result in electric shock, fire, and /or serious injury.

 

When using the product, the safety rules must be 

followed. For your safety and that of bystanders, read 

these instructions before operating the product. Keep 

the instructions safe for later use.

 

The product is not intended to be used by children or 

persons with reduced physical, mental, or sensory 

capabilities. Children should be adequately supervised 

to ensure that they do not play with the product.

 

Some regions have regulations that restrict the use of 

the product. Check with your local authority for advice.

TRAINING

 

Read the instructions carefully. Be familiar with all 

controls and the proper use of the product.

 

Never allow children or people who are unfamiliar with 

these instructions to use the product. Local regulations 

may restrict the age of the operator.

 

Keep bystanders, children, and pets 15 m away from the 

area of operation. Turn off the product if anyone enters 

the area.

 

Never use the product while tired, ill, or under the 

influence of alcohol, drugs, or medication.

 

Keep in mind that the operator or user is responsible for 

accidents or hazards occurring to other people or their 

property.

PREPARATION

 

Wear full eye and hearing protection while operating the 

product. If working in an area where there is a risk of 

falling objects, head protection must be worn.

 

Hearing protection may restrict the operator’s ability 

to hear warning sounds. Pay particular attention to 

potential hazards around and inside the working area.

 

Wear heavy, long trousers, boots, and gloves. Do not 

wear loose-fitting clothing, short trousers, or jewellery of 

any kind. Do not use the product with bare feet.

 

Secure long hair so that it is above shoulder level to 

prevent entanglement in moving parts.

 

Before use and after any impact, check that there are no 

damaged parts on the product. A defective switch or any 

part that is damaged or worn should be properly repaired 

or replaced by an authorised service centre.

 

Make sure that the cutting attachment is properly 

installed and securely fastened.

 

Never operate the product unless all guards, deflectors, 

and handles are properly and securely attached.

 

Consider the environment in which you are working. 

Keep the working area free from wires, sticks, stones, 

and debris, which if struck by the cutter, can become 

thrown objects.

BATTERY TOOL USE AND CARE

 

Recharge only with the charger specified by the 

manufacturer. A charger that is suitable for one type of 

battery pack may create a risk of fire when used with 

another battery pack.

 

Use power tools only with specifically designated battery 

packs. Use of any other battery packs may create a risk 

of injury and fire.

 

When the battery pack is not in use, keep it away from 

other metal objects, like paper clips, coins, keys, nails, 

screws, or other small metal objects that can make a 

connection from one terminal to another. Shorting the 

battery terminals together may cause burns or a fire.

 

Under abusive conditions, liquid may be ejected from 

the battery; avoid contact. If contact accidentally occurs, 

flush with water. If liquid contacts eyes, additionally seek 

medical help. Liquid ejected from the battery may cause 

irritation or burns.

LINE TRIMMER SAFETY WARNINGS

 

Never allow children, persons with reduced physical, 

sensory, or mental capabilities, or lack of experience 

and knowledge, or people who are unfamiliar with the 

instructions to use the product.

 

Use the product in daylight or with good artificial light.

 

Avoid using the product on wet grass.

 

Keep firm footing and balance at all times, and be sure 

of proper footing on slopes.

 

Do not walk backwards when using the product. Walk, 

never run.

 

Keep the head attachment below waist level.

 

Never use the product with damaged guards or without 

guards in place.

 

Never fit a metal replacement line.

 

Keep hands and feet away from the cutting means at all 

times, especially when turning on the motor.

Summary of Contents for R18XLTR20

















Reviews: