10
Remove the battery. Remove the pad by pulling it down
and away from the nose. To replace the pad, fit it into place
over the nose and push up to reseat.
On-board storage for the pad is located on the magazine of
the tool. An extra no-mar pad is provided in the on-board
storage area.
LOADING THE TOOL WITH BRAD NAILS
See Figures 5 - 6.
WARNING
Keep the tool pointed away from yourself and others
when loading nails. Failure to do so could result in
possible serious personal injury.
■ Remove battery pack from the tool, if installed.
■ With the nose of the tool pointed away from you,
squeeze magazine release button located at the rear
of the magazine and slide the magazine cover open.
■ Place the brad nails in the channel with the nail tips
pointing down. Ensure that the nail tips rest on the
bottom of the channel and the nail heads are seated
in the slot.
■ Push the magazine cover closed until it securely snaps
into place.
■ Make sure that the magazine is securely locked in
place.
■ Reinstall battery, and reactivate nailer by pressing the
work light grip switch.
SETTING THE AIR PRESSURE
See Figure 7.
The amount of air pressure required will depend on the size
of the nail and the workpiece material.
Begin testing the depth of drive by driving a test nail into
the same type of workpiece material used for the actual job.
■ Remove battery pack from the tool, if installed.
■ Turn air pressure dial clockwise to increase air pressure
or counterclockwise for decreased pressure.
It may be possible to achieve the desired depth with air
pressure adjustments alone. If finer adjustments are
needed, use the depth of drive adjustment on the tool.
DEPTH OF DRIVE ADJUSTMENT
See Figure 8.
NOTE:
If 50mm (2”) nails are driven into seasoned
hardwood thicker than 30mm, they may not drive in fully.
The driving depth of the nail may be adjusted beyond
air pressure. It is advisable to test the depth on a scrap
workpiece to determine the required depth for the
application.
To determine depth of drive, first adjust the air pressure
and drive a test nail. To achieve the desired depth, use the
depth of drive adjustment on the tool. Harder materials and
longer nails will require more force to drive the nail.
■ Remove battery pack from the tool, if installed.
■ Turn the depth of drive adjustment left or right to change
the driving depth.
■ Reinstall battery and reactivate the tool by pressing the
work light grip switch.
■ Drive a test nail after each adjustment until the desired
depth is set.
NOTE:
Set depth of drive at the shallowest depth that
will meet your needs.
DRIVING BRAD NAILS
See Figure 9 .
WARNING
Never wedge or hold back the workpiece contact
mechanism during operation of the tool. Doing so could
result in possible serious injury.
Single sequential actuation mode:
This nail gun employs single sequential actuation mode:
■ Install the battery. Reactivate tool.
■ Grip the tool firmly to maintain control. Position the nose
of the tool onto the work surface.
■ Push the tool against the work surface to depress the
workpiece contact.
■ Squeeze the trigger to drive a nail.
■ Always remove your finger from the trigger when the
desired number of nails has been driven.
NOTE:
Hold trigger until drive cycle is complete.
DRY-FIRE LOCKOUT
When the magazine has 0-5 nails remaining, the dry-fire
lockout feature will not allow continued operation.
To resume operation, reload the tool with nails.
LED WORK LIGHTS
See Figure 10.
■ Press LED work light grip switch while firmly holding
tool during normal operation.
DIAGNOSTIC FEEDBACK
The LED work lights provide feedback to indicate whether
the battery pack is charged sufficiently and/or if the tool is
functioning properly.
If work lights are flashing, install fully charged battery. If
light continue to flash, see
Troubleshooting
section for
more information.
REMOVING NAILS FROM THE TOOL
See Figure 11.
WARNING
Remove the battery pack before removing nails or
clearing a jammed nail. Failure to do so could result in
serious personal injury.
