Ryobi R18MT Original Instructions Manual Download Page 3

Page: 3 / 130

Safety, performance, and dependability have been given
top priority in the design of your multi-tool.

INTENDED USE

The multi-tool is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual and can be considered responsible for their
actions.

The multi-tool is intended to be used:

–

for sanding and finishing metal, wood, plastics, or
similar materials using the sanding pad with the
shaped abrasive sheets provided

–

for scraping and plunge-cutting into non-ferrous
metal, wood, plastics, plasterboard, etc. using the
provided metallic cutting blades

–

for cutting holes in walls to accommodate switches
or power sockets

–

for removing grouting from between ceramic tiles

The multi-tool is intended to be operated indoors in dry, well
illuminated and adequately ventilated conditions.

The multi-tool is not intended to be used on wet materials
or surfaces.

Do not use the product in any way other than those stated
for intended use.

WARNING

Read all safety warnings and all instructions.

Failure

to follow the warnings and instructions may result in
electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference

MULTI-TOOL SAFETY WARNINGS

■

Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.

Cutting

accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.

■

Always wear safety goggles while operating the tool.
Wear a dust mask when dust is produced.

WARNING

Dust from certain paints, coatings, and materials may
cause irritation or allergic reactions. Dust from wood
such as oak, beech, MDF, and others are carcinogenic.
Only quali

ed specialists should be allowed to use the

product on materials containing asbestos.

WARNING

The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when not using
it. Disconnecting the product from the power supply
will prevent accidental starting that could cause serious
injury.

■

When working in walls, ceilings or floors, take care to
avoid electric cables and gas or water pipes.

WARNING

Metallic accessories will become hot during use and
could result in skin burns if contacted by the operator.
Wear gloves when changing accessories.

Take care when setting down the tool between
operations to prevent damage or injury.

■

Do not use cutting accessories which are damaged,
cracked or do not fit securely to the product.

■

The multi-tool creates vibrations which move the
accessory. The vibrations may cause discomfort if the
product is operated for long periods of time. Take a rest
often, especially if you feel discomfort in the arm, wrist,
or fingers. Choose a speed setting which will get the
work completed efficiently. Read the Residual Risks
and Risk Reduction sections for more information on
vibration-related injury.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national
provisions and regulations.

Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:

■

Injury caused by dust

–

Wear eye protection at all times.

–

Wear respiratory protection masks containing filters
appropriate to the materials being worked. Ensure
adequate workplace ventilation.

–

Do not eat, drink or smoke in the work area.

■

Injury caused by noise and vibration

–

Wear ear protection.

–

Do not operate the product for long periods of time.
See “Risk reduction”.

■

Risk of electrocution if electric cables are cut

–

Always hold the product by designated handles. Do
not touch the cutting blades or metal parts of the
product.

RISK REDUCTION

It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,

English