Ryobi ONE+ R18TR-0, Original Instructions Manual

Page: 5 / 16

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■ Injury caused by vibration
– Limit exposure. See Risk Reduction.
■ Injury caused by flying debris
– Wear eye protection at all times.
■ Injury caused by dust
–
Wear appropriate dust mask with suitable filters that
can protect against particles from the material of the
workpiece. Do not eat, drink, or smoke in the work
area. Ensure adequate ventilation and use the dust
extraction accessories provided.
■ Injury from contact with the cutting bits
–
The bits are sharp and will become hot during use.
Wear gloves when changing bits. Keep hands away
from the cutting area at all times. Never hold the
workpiece being cut in your hands or across your
leg. Secure the workpiece whenever possible.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■ Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
■ After each period of operation, exercise to increase
blood circulation.
■ Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
Injuries may be caused or aggravated by prolonged use
of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
ASSEMBLY
WARNING
Do not use this product if it is not completely assembled
or if any parts appear to be missing or damaged. Use of
a product that is not properly and completely assembled
or with damaged or missing parts could result in serious
personal injury.
WARNING
Do not attempt to modify this product or create
accessories or attachments not recommended for use
with this product. Any such alteration or modification is
misuse and could result in a hazardous condition leading
to possible serious personal injury.
MAINTENANCE
WARNING
The product should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product will prevent
accidental starting that could cause serious injury.
■ When servicing, use only original manufacturer’s
replacement parts. Use of any other parts may create a
hazard or cause product damage.
WARNING
For greater safety and reliability, all repairs should be
performed by an authorised Ryobi service centre.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.
WARNING
Do not, at any time, let brake fluids, gasoline, petroleum-
based products, and penetrating oils, come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
The dust from plaster and wall board is abrasive and may
cause premature failure of the product if it is allowed to
enter the motor area. Always use the dust extraction
accessory connected to a vacuum. Thoroughly clean the
3