![background image](http://html1.mh-extra.com/html/ryobi/hld-120/hld-120_owners-operating-manual_1504468005.webp)
1. Keyless chuck
2. Torque adjustment cap
3. Forward/ Reverse switch
4. LED work light
5. Trigger
6. Battery clip
7. Battery pack
8. Belt hook
9. Charging adaptor
10. Charging jack
Battery
Chuck capacity
No load speed
Max torque
Drilling capacity
Clutch position
Charging time
Net weight
12V, 1,300mAh Li-ion
10mm
0-700min
-1
12Nm
steel: 8mm
wood: 16mm
21 + 1
3-5hours
1.0kg
APPLICATIONS
(Use only for the purposes listed below.)
1. Drilling wood, ceramics, plastics, fiberglass, metal and concrete.
2. Driving and removing machine screws, wood screws, tapping
screws etc.
TRIGGER (Fig. 3)
FORWARD/ REVERSE SWITCH (Fig. 3)
KEYLESS CHUCK AND MOUNTING THE BIT (Fig. 1)
This tool comes equipped with a keyless chuck to easily mount
the bit.
Insert the bit into the chuck as far as it will go and rotate the chuck
clockwise to securely tighten the bit.
The bit can be removed by turning the chuck counterclockwise.
WARNING!
Make sure to insert the drill bit straight into the chuck
jaws. Do not insert the drill bit into the chuck jaws at an angle then
tighten (Fig. 2). This could cause the drill bit to be thrown from the
drill, resulting in possible serious personal injury or damage to the
chuck.
This tool is started and stopped by depressing and releasing the
trigger (5).
The drill speed is variable from 0 through 700 by controlling the
trigger-squeezing force.
To change the direction of rotation, stop the tool by releasing the
trigger and push the forward/ reverse switch (3) to the opposite
side. When the reversing switch is set to the right position, the
direction of rotation will be clockwise when viewed from the handle
end of the drill. When the reversing switch is set to the left position,
the direction of rotation will be counter-clockwise.
The trigger can be locked by positioning the reversing switch at
the center. Lock the trigger whenever the tool is not in use.
LED WORK LIGHT (Fig. 3)
This tool is equipped with a LED work light (4) to illuminate the tip
of a bit. The light turns on by depressing the trigger.
FASTENING TORQUE ADJUSTMENT (Fig. 4)
CHARGING BATTERY PACK (Fig. 5, 6)
This tool is equipped with a clutch which enables the fastening
torque to be adjusted in 21 stages.
To use the tool in the screwdriver mode, set one of the numbers “1”
to “21” indicated on the torque adjustment cap (2) to the marked
( ) on the top side of housing. The higher number on the torque
adjustment cap, the greater the torque.
To use the tool in the drill mode, set the drill mark ( ) on the
torque adjustment cap to the point. The clutch does not operate
when the tool is used in the drill mode.
The battery pack for the tool has been shipped in a low charge
condition to prevent possible problems. Therefore, you should
charge it prior to use.
NOTE:
Batteries will not reach full charge the first time they are
charged. Allow several cycles for them to fully charge.
• Charge battery pack only with the charger provided.
• D
o not place charger in an area of extreme heat or cold. It will
work best at temperatures above 10°C and below 38°C.
• M
ake sure power supply is normal house voltage, 230 volts,
50Hz, AC only.
CAUTION!
Summary of Contents for HLD-120
