![background image](http://html1.mh-extra.com/html/ryobi/ebs-1310v/ebs-1310v_user-manual_1505739006.webp)
2
English
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
DUST BAG (FIG. 2)
When sanding wood, the dust bag (5) should be used.
Although the dust bag has a substantial capacity, it
should be emptied frequently.
Opening the zipper of the dust bag allows complete
cleaning.
CAUTION!
When sanding metal, the dust bag should not be
used, because of the risk of fire from flying
sparks.
CHANGING THE ABRASIVE BELT(FIG.3 TO 5)
WARNING!
BE SURE TO DISCONNECT THE TOOL FROM
THE POWER SUPPLY WHEN MOUNTING AND
REMOVING THE SANDING BELT.
■
Place the tool on its side and lift the lever (3) to retract
the front roller and release the belt tension (Fig. 3).
■
Pull the sanding belt off.
If the belt tension is not released after lifting the lever,
loosen the adjustment knob (9) (Fig. 4).
■
Mount a new sanding belt.
NOTE!
Be sure that the arrow inside of the belt is pointing in
the same direction as that of the tool.
■
Push the lever down to the original position (Fig. 5).
CAUTION!
Ensure that your fingers are not trapped.
TRACKING ADJUSTMENT (FIG. 6)
The belt life will be increased by using the tracking
adjustment.
Turn the tool upside down and hold it firmly with one
hand, then start the tool and observe the tracking of the
sanding belt.
Stop the tool and adjust the tracking of the belt by rotating
the tracking knob until the edge of the belt is even with
the outer edges of both the front and rear rollers.
CAUTION!
Check that the belt does not rub against the
tool’s frame.
OPERATING (FIG. 7)
NEVER COVER AIR VENTS SINCE THEY MUST
ALWAYS BE OPEN FOR PROPER MOTOR COOLING.
MAKE SURE THAT THE WORK PIECE IS FREE OF
NAILS AND OTHER FOREIGN OBJECTS THAT
COULD TEAR THE ABRASIVE BELT.
Hold the tool firmly with both hands. Turn the switch on
and permit the rotation of the abrasive belt to reach full
speed. Then gently place the tool on the work piece
surface. Move the tool back and forth. Never exert
excessive pressure on the tool. The weight of the tool
applies adequate pressure. Excessive pressure will retard
the abrasive action, leave an uneven finish and cause
extra wear to both the tool and the abrasive belt. Always
lift the tool off the work piece before turning the switch off.
CLAMP
(Optional accessory)
The clamp is designed to stabilize the tool when using it
tin the bench configuration.
MOUNTING & ADJUSTING THE OPTIONAL
SANDING FRAME (FIG. 8)
Put the belt sander on the sanding frame and attach four
slot into slot holder (14).
By turning the adjustment bolt counterclockwise, the
sanding frame will down and can be taken out. If turning
clockwise, it will raise and the depth will be added.
Fine adjustment of the abrasive action is possible by
turning the adjustment bolt (13).
MAINTENANCE
After use, check the tool to make sure that it is in top
condition. It is recommended that you take this tool to a
Ryobi Authorized Service Centre for a thorough cleaning
and lubrication at least once a year.
DO NOT MAKE ANY ADJUSTMENT WHILE THE
MOTOR IS IN MOTION. ALWAYS DISCONNECT THE
POWER CORD FROM THE RECEPTACLE BEFORE
CHANGING REMOVABLE OR EXPENDABLE PARTS
(BLADE, BIT, SANDING PAPER, ETC.), LUBRICATING
OR WORKING ON THE UNIT.
WARNING!
To ensure safety and reliability, all repair should
be performed by an AUTHORIZED SERVICE
CENTRE or other QUALIFIED SERVICE
ORGANIZATION.
961067431-01_EBS-9576V&EBS-1310V_EU.indd Sec2:2
961067431-01_EBS-9576V&EBS-1310V_EU.indd Sec2:2
2010.4.21 11:32:20 AM
2010.4.21 11:32:20 AM