Ryobi Draft RAG600-115 Original Instructions Manual Download Page 7

5

 WARnInG

To ensure safety and reliability, all repairs should be 

performed by an authorised service center or other 

qualified service organisation.

 WARnInG

Do not use compressed air to blow dust from the product. 

This practice is dangerous and can cause dirt and grit to 

be blasted into someone’s eyes, causing serious injury.

enVIROnMentAL PROtectIOn 

Recycle raw materials instead of disposing 

of as waste. The machine, accessories and 

packaging should be sorted for environment-

friendly recycling.

sYMBOLs On tHe PROduct

Safety Alert

V

Volts

Hz

Hertz

Alternating current

W

Watts

n

Rated speed

min־¹

Revolutions or reciprocations per minute

Class II tool, double insulation

Please read the instructions carefully before 

starting the product.

Wear ear protection

Wear eye protection

Wear dust mask.

Do not use chipped, cracked or defective 

grinding wheel

Not for wet grinding. Using water or other 

liquid coolants may result in electrocution or 

shock.

Wear safety hand gloves

CE Conformity

EurAsian Conformity Mark

Ukrainian mark of conformity

Waste electrical products should not be 

disposed of with household waste. Please 

recycle where facilities exist. Check with your 

local authority or retailer for recycling advice.

sYMBOLs In tHIs MAnuAL

Connect to the power supply.

Disconnect from the power supply. 

Parts or accessories sold separately

Waste electrical products should not 

be disposed of with household waste. 

Please recycle where facilities exist. 

Note

Warning

Lock

Unlock

Stop the product.

The following signal words and meanings are intended to 

explain the levels of risk associated with this product:

 dAnGeR

Indicates an imminently hazardous situation, which, if not 

avoided, will result in death or serious injury.

 WARnInG

Indicates a potentially hazardous situation, which, if not 

avoided, could result in death or serious injury.

 cAutIOn

Indicates a potentially hazardous situation, which, if not 

avoided, may result in minor or moderate injury.

cAutIOn

(Without Safety Alert Symbol) Indicates a situation that 

may result in property damage.

Summary of Contents for Draft RAG600-115





















Reviews: