Ryobi Draft RAG600-115 Original Instructions Manual Download Page 17

GuARAntee

In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.
1.  The guarantee period is 24 months for consumers and commences on the date when the product was purchased. 

This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to 

consumer and private use only. So there is no guarantee provided in case of professional or commercial use.

2. 

There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period 

described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed 

in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from 

the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the 

online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the 

data which are required to enter online and they have to accept the terms and conditions. The registration confirmation 

receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the 

extended warranty. Your statutory rights remain unaffected.

3.  The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material 

at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations 

including but not limited to incidental or consequential damages. The warranty is not valid if the product has been 

misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to

 

any damage to the product that is the result of improper maintenance

 

any product that has been altered or modified

 

any product where original identification (trade mark, serial number) markings have been defaced, altered or 

removed

 

any damage caused by non-observance of the instruction manual

 

any non CE product

 

any product which has been attempted to be repaired by an non-qualified professional or without prior authorization 

by Techtronic Industries

 

any product connected to improper power supply (amps, voltage, frequency)

 

any damage caused by external influences (chemical, physical, shocks) or foreign substances

 

normal wear and tear of spare parts

 

inappropriate use, overloading of the tool

 

use of non-approved accessories or parts

 

carburettor after 6 months, carburettor adjustments after 6 months

 

power tool accessories provided with tool or purchased separately. Such exclusions include but is not limited to 

screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide

 

components (parts and accessories) subject to natural wear and tear, including but not limited to carbon brushes, 

chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube

4.  For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the 

following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product 

to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely 

packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short 

description of the fault.

5. 

A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the 

guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will 

have to be paid by the sender.

6.  This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. 

Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.

Summary of Contents for Draft RAG600-115





















Reviews: