background image

Page 7

ASSEMBLY

Carefully remove the saw and accessories from box.
Make sure all items listed in the Packing List are included.

Do not discard the packing material until you have carefully
inspected and satisfactorily operated saw.

Examine all parts and accessories to make sure that no
breakage has occurred during shipping. Any damaged
part should be replaced before attempting to use the tool.

WARNING:

Your saw should never be connected to a power supply
when you are assembling parts, making adjustments,
assembling or removing blades, cleaning, or when not in
use. Disconnecting your saw will prevent accidental
starting that could cause serious personal injury.

WARNING:

7-1/4 in. (184 mm) blade is the maximum blade capacity
of your saw.  Also, never use a blade that is too thick to
allow outer blade washer to engage with the flat on the
spindle. Larger blades will come in contact with the blade
guards, while thicker blades will prevent blade screw from
securing blade on spindle. Either of these situations could
result in a serious accident.

TO ASSEMBLE OR REMOVE BLADE

See Figure 2.

Unplug your saw.

WARNING:

Failure to unplug your saw could result in accidental
starting causing possible serious personal injury.

Depress spindle lock button to secure blade when turning
blade screw. 

See Figure 3.

Remove spring washer and outer blade washer ("D"
washer). NOTE: BLADE CAN BE REMOVED AT THIS
POINT.
 If you are assembling blade for the first time or
changing blade, continue to follow the steps on Page 8.

Circular Saw
7-1/4 Blade
Wrench

Fig. 2

SPINDLE

LOWER BLADE

GUARD HANDLE

BLADE

OUTER BLADE

WASHER

("D" WASHER)

BLADE

SCREW

SPRING

WASHER

INNER

FLANGE BUSHING

PACKING LIST

Warranty Card
Carrying Case
Operator's Manual

Summary of Contents for CSB1308





















Reviews: