![background image](http://html1.mh-extra.com/html/ryobi/cro1800/cro1800_operators-manual_1506185010.webp)
10
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a second is
suffi cient to infl ict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating products. Failure to do so could
result in objects being thrown into your eyes, resulting in
possible serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
J
Sanding on wood surfaces
J
Removing rust from and sanding steel surfaces
CAUTION:
If at any point during the charging process none of the
LEDs are lit, remove the battery pack from the charger
to avoid damaging the product. DO NOT insert another
battery. Return the charger and battery to your nearest
service centre for service or replacement.
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
J
Red LED on = Fast charging mode.
J
Green LED on = Fully charged and in maintenance charge
mode.
J
Green LED on = When battery pack is inserted into
charger, indicates hot battery pack or that battery pack
is out of normal temperature range.
J
Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
J
No LED on = Defective charger or battery pack.
CHARGING THE BATTERY PACK
Battery packs for this product have been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until the green LED on the front of the
charger comes on.
OPERATION
NOTE: Batteries will not reach full charge the fi rst time they
are charged. Allow several cycles (operation followed by
recharging) for them to become fully charged.
CHARGING A COOL BATTERY PACK
If battery pack is within normal temperature range, the red
LED on charger will come on.
NOTE: If the charger does not charge the battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Authorised Service Centre for
electrical check.
J
Charge the battery pack only with the charger provided.
J
Make sure the power supply is normal household
voltage, 240 volts, 50 Hz, AC only.
J
Connect the charger to the power supply.
J
Place the battery pack in the charger aligning raised
rib on the battery pack with the groove in the charger.
See Figure 2.
J
Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
J
Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
J
Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is
in maintenance charge mode.
NOTE: The green LED will remain on until the
battery pack is removed from the charger or charger is
disconnected from the power supply.
J
If both yellow and green LEDs come on, this indicates
a deeply discharged or defective battery pack.
Allow the battery pack to remain in the charger for 15
to 30 minutes. When the battery pack reaches normal
voltage range, the red LED should come on. If the
red LED does not come on after 30 minutes, this may
indicate a defective battery pack that should be
replaced.
J
After normal usage, a minimum of 1 hour of charging time
is required to fully recharge battery pack.
J
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
J
Do not place the charger and battery pack in an area of
extreme heat or cold. They will work best at normal room
temperature.
NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 0°C but
less than 37°C.
J
When batteries become fully charged, unplug the
charger from power supply and remove the battery
pack.