![background image](http://html.mh-extra.com/html/ryobi/cjs1802k/cjs1802k_operators-manual_1505725004.webp)
nails, screws or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact accidentally
occurs, flush with water. If liquid contact eyes,
additionally seek medical help.
Liquid ejected from
the battery may caused irritation or burns.
SERVICE
Have your power tool serviced by an authorised
Ryobi service centre using only identical replacement
parts.
This will ensure that the safety of the power
tool is maintained.
RULES FOR SAFE OPERATION
Page 2
BATTERY TOOL USE AND CARE
Ensure the switch is in the off position before
inserting battery pack.
Inserting the battery pack
into power tools that have the switch on invites accidents.
Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
Use power tools only with specifically designated
battery packs.
Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
TO INSTALL BATTERY PACK (fig. 2)
To install, insert battery pack neck into the saw's battery
port, making sure the latches on each side snap into
place and battery pack is secure before beginning
operation.
To remove, locate latches on side of battery pack and
depress both sides to release.
FITTING BLADE (fig. 3)
Before installing blade, remove the battery pack.
The tool-less blade clamp fits T-shank blade. To fit the
blade simply lift up the blade clamp lever. Insert the
blade fully into the spindle slot.
GENERAL CUTTING (fig. 4)
Rest the front of the base plate on the workpiece and
align cutting edge of the blade with the line on your
workpiece. Start your saw and move it forward on the
work surface. Apply downward pressure to keep the
saw steady and only enough forward pressure to keep
the blade cutting
ANGLE CUTTING
The saw may be adjusted for bevel cutting angles up
to 45
o
to the left and right, angles are marked in 15
o
increments on the base.
DISPOSAL OF AN EXHAUSTED BATTERY
To preserve natural resources please recycle or dispose
of the battery properly.
This product contains nickel-cadmium batteries.
Consult your local waste authority for information regarding
available recycling and /or diposal options.
PREPARING BATTERY PACK FOR RECYCLING
After removing, cover the battery pack's terminals with
heavy-duty adhesive tape.
Do not attempt to destroy or take the battery pack apart
or remove any of its components. Do not touch both
terminals with metal objects or body parts or a short
circuit may result. Keep away from children. Failure to
comply with these warnings could result in fire and / or
serious injury.
CONTENTS OF BOX
18.0V cordless jigsaw, 2 wood cutting blades, 2 metal
cutting blades, 2 battery packs, charger.
OPERATING INSTRUCTIONS
CHARGING THE BATTERY PACK (fig. 1)
The battery packs for this tool have been shipped in a
low charge condition to prevent possible problems.
You should, therefore, charge them prior to use.
Note:
Batteries will not reach full charge the first time
they are charged. Allow several cycles (drilling followed
by recharging) for the item to fully charge. The battery
charger should only be used indoors.
Make sure power supply is normal house voltage,
240volts, 50Hz AC only.
Place the battery pack into the charger as indicated.
Align raised rib on battery pack with groove in charger.
Press down on battery pack to make sure contacts
on battery pack engage properly with contacts in charger.
When properly connected, the red light on charger will
turn on.
After normal usage, 1 hour of charging time is required
for the battery to be fully charged.
Note: Normally the red light on the charger will come
on, this indicates charge mode. If the green and yellow
lights come on, remove the battery pack, wait 1 minute
and reinsert battery pack in charger. If the green and
yellow lights continue to remain on an additional 15
minutes, the battery pack is damaged and will not accept
charge. A maximum charge time of 1-1 1/2 hours is
required to recharge a completely discharged battery.
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a problem.
Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
When the batteries become fully charged, the green
light on charger will turn on. Unplug the charger from
power supply and remove the battery pack.
LED FUNCTION OF CHARGER
Red
Fast charging mode
Green and yellow
Control charge or defective
Green
Fully charged
OPERATION